Document Outline

• Contents
  • Safety Instructions
  • Table of Contents
  • Chapter 1: Introduction
    • PROGRAMMING ISACC
    • LEARNING TO USE ISACC
    • ABOUT THE MANUAL
      • IMPORTANT!
  • Chapter 2: Installation
    • COMPLETE PACKAGE INSTALLATION (FGD-5000)
      • UNPACKING ISACC
      • GROUNDING WRIST STRAP
    • OPERATING ENVIRONMENT
    • MOUNTING ISACC
    • STRAIN RELIEF
    • POWERING ISACC
    • ADDITIONAL SURGE PROTECTION
    • BACKUP BATTERY
    • LITHIUM BATTERY
    • TURNING ISACC ON
    • RESET BUTTON
    • BUZZER
    • PHONE LINE INSTALLATION
    • BOARD LEVEL INSTALLATION (FGD-5100)
      • UNPACKING ISACC
      • GROUNDING WRIST STRAP
      • OPERATING ENVIRONMENT
      • MOUNTING ISACC
      • POWERING ISACC
        • AC supply requirements:
        • AC supply connections:
        • DC supply requirements:
        • DC supply connections:
      • GROUNDING ISACC
      • BACKUP BATTERY
      • LITHIUM BATTERY
      • TURNING ISACC ON
      • RESET BUTTON
      • BUZZER
      • PHONE LINE INSTALLATION
      • FCC REQUIREMENTS
        • Canadian Department of Communications NOTICE
  • Chapter 3: Communication Setup
    • SETUP FOR PC
      • LOCAL COMMUNICATION THROUGH RS232 PORT
    • SETUP FOR TERMINAL
      • LOCAL COMMUNICATION THROUGH RS232 PORT
      • REMOTE COMMUNICATION VIA MODEM
      • ISACC RS232 SPECIFICATIONS
      • NETWORK WIRING
  • Chapter 4: Inputs
    • HOW THE INPUTS WORK
    • INPUT TERMINAL BLOCK
    • WIRING SENSORS TO THE INPUTS
      • SHIELDED WIRE
      • LENGTH OF WIRE
    • INPUT MODULES
      • To use the 4-module rack with ISACC:
      • To wire the logic I/O (right side) to ISACC:
      • To wire the field I/O (left side) to the input device:
    • DIP CONNECTOR FOR A 16-MODULE RACK
      • To use the 16-module rack:
    • ISACC INPUT SPECIFICATIONS
    • INPUT MODULE SPECIFICATIONS
      • AC Input Module (FGD-0018):
      • DC Input Module (FGD-0017):
  • Chapter 5: Outputs
    • HOW THE OUTPUTS WORK
    • OUTPUT TERMINAL BLOCKS
    • WIRING THE MECHANICAL RELAY
      • To wire a device to the mechanical relay using an ISACC power supply:
      • To wire a device to the mechanical relay using an external power source:
    • WIRING THE DIGITAL OUTPUTS
    • WIRING THE ANALOG OUTPUTS
    • OUTPUT SPECIFICATIONS
      • DIGITAL:
      • ANALOG:
      • RELAY:
      • BUZZER:
      • SOLID STATE RELAY SPECIFICATIONS
        • AC Output Module (FGD-0015):
        • DC Output Module (FGD-0016):
        • High Power Solid State Relay (FGD-0020):
  • Chapter 6: Power Supplies
  • Chapter 7: Programming
    • KEYWORDS
    • SYSTEM
    • CLOCK
    • INPUTS
    • ITYPE
    • TABLE
    • LIMITS
    • RECOGNITION
    • ALARMS
    • DIALOUT
    • OUTPUTS
    • ONAME
    • PHONE
    • SELECTION
    • VOICE
    • LOGGING
    • NETWORK
    • VARIABLES
    • STAND ALONE COMMANDS
      • RESET
      • CLEAR
      • PATCH
      • HELP
      • EXIT
      • DATA
      • 123
      • DIAG
  • Chapter 8: Programming
    • SPECIFICATIONS
    • ABOUT THE C LANGUAGE
    • STRUCTURE
    • EDITING COMMANDS
      • INSERT
      • DELETE
      • ERASE
      • LIST
    • STAND ALONE COMMANDS
      • COMPILE
      • RUN
      • START & STOP
    • C LANGUAGE KEYWORDS
    • PREDEFINED VARIABLES
      • MONTH, DAY, YEAR, HOURS, MINUTES & SECONDS
      • EXISTS & UPTIME
    • FUNCTION LIBRARY
      • ALARM
      • DATA
      • ENABLE
      • INPUT
      • IS_ALARM
      • NETWORK
      • OUTPUT
      • OUT_SPEC
      • PUTNUM
      • PUTS
      • RESET
      • RELOAD
      • SET_INPUT
    • ARRAYS
      • SAMPLE PROGRAM:
    • ERROR HANDLING
    • DIFFERENCES BETWEEN STANDARD C AND ISACC C
    • PROGRAMMING EXAMPLES
    • COMMON ISACC PROGRAMMING ERRORS
  • Chapter 9: Operation
    • HOW THE UNIT WORKS
    • ALARM DIALOUT - VOICE MODE
    • ALARM DIALOUT - DATA MODE
    • ALARM DIALOUT - BEEPER
    • CALL PROGRESS
    • STATUS REPORT - VOICE MODE
    • VOICE MODE OUTPUT CONTROL
    • STATUS REPORT - DATA MODE
    • DATA LOGGER
    • EXTERNAL MODEM
  • Chapter 10: Glossary
  • Appendix A: Checking for Proper Operation
  • Appendix B: Engineering Specifications
  • Appendix C: Board Layout
  • Appendix D: Mounting I/O Devices
  • Appendix E: Accessories
  • Appendix F: Return for Repair
  • Warranty