Philips CEM220 - Manual

Register your product and get support at CEM220
EN Quick Start Guide
3 4
2
A1 A2 A3 A4 A5 A6 A7 A8 B1 B2 B3 B4 B5 B6 B7 B8
A
A B
a b c d
B
b
a
c
d
a a b c d
a b
e f
c d
g h i
b
c
d
1
a b
e f g
c
h
d
Overview of parts 1
These are the supplied parts needed to
connect and install this unit.
1 In-car audio system
2 Sleeve
3 Front panel
4 Standard connector
5 Trim plate (2 pieces)
6 Rubber cushion
7 Disassembly tools
8 Screws 4 pieces
Connect wires
Caution
Ensure that all loose leads are insulated with •
electrical tape.
For cars with ISO connectors 2 3
1 Pull out the ISO connectors from car
dashboard and connect them to the bigger
end of the supplied standard connector.
2 Connect the other end of the supplied
standard connector to the unit.
3 Connect the antenna and amplifi er as
illustrated, if applicable.
Connector Connect to
1 REAR LINE OUT R Rear right
speaker
2 REAR LINE OUT L Rear left speaker
3 SUB OUT Subwoofer
4 ANTENNA Antenna
For cars with ISO connectors 3 4
Caution
Be sure to connect the black ground (earth) •
lead fi rst.
1 Connect the antenna and amplifi er as
illustrated, if applicable.
2 Cut off the bigger end of the supplied stan-
dard connector.
3 Check the car’s wiring carefully and connect
them to the supplied standard connector.
4 Connect the supplied standard connector to
the unit.
1 Green/black
strip Left speaker
(Rear)
2 White/black
strip Left speaker
(Front)
3 Gray/black
strip Right speaker
(Front)
4 Purple/black
strip Right speaker
(Rear)
e RED Ignition key +12V DC
when ON/ACC
f BLUE Motor/electric antenna
relay control lead/
Amplifi er relay control
lead
g BLACK Ground
h Orange/
white
Illumination switch
i YELLOW To the +12V car battery
which is energized at all
times
Note
Check wire connection before you mount •
the unit into a car.
If preset radio stations are lost when the
•
ignition key is turned OFF and then back
ON, reconnect the red leads crosswise to
the yellow ones.
Attach the front panel 5
1 Attach the trim plate.
2 Insert the right side of the panel in the
chassis until it is correctly engaged.
3 Press the left side of the panel and point
the left hole at the left pillar.
4 Release the panel to engage the left side.
Mount in the dashboard 5
1 If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
If you disconnect the car battery in a car that •
has an on-board drive or navigation computer,
the computer may lose its memory.
If the car battery is not disconnected,
•
to avoid short-circuit, ensure that bare
wires do not touch each other.
2 Remove the two screws on the top of the
unit.
3 Remove the mounting sleeve with the
supplied disassembly tools.
4 Ensure that car dashboard opening is
within these measurements:
5 Install the sleeve into the dashboard and
bend the tabs outward to fi x the sleeve.
6 Place the rubber cushion over the end of
the bolt.
7 Slide the unit into the dashboard until you
hear a click sound.
8 Reconnect the negative terminal of the car
battery.
Turn on
1 Press z to turn on the unit.
• To turn off the unit, press z for 3
seconds.
Set clock
1 Press MENU/DISP for 3 seconds.
2 Press 3 or 4 repeatedly to until the cur-
rently time is displayed.
3 Turn z clockwise to set hour.
4 Press z to confi rm.
5 Turn z anti-clockwise to set minute.
6 Press z to confi rm.
View clock
1 Press MENU/DISP repeatedly until the clock
is displayed.
Listen to radio
1 Press SOURCE repeatedly to select Radio.
2 Press or to select band: [FM1], [FM2],
[FM3], [AM1], or [AM2] .
3 Press ∞ or § to tune to a radio station
manually.
5
5mm
5mm
To search for a radio station •
automatically, press SEARCH.
Play audio fi les
1 Press on the front panel to release the
panel.
2 Insert a CD with the printed side facing up.
3 Close the panel.
4 Press 2; , to start play.
To pause CD play, press • 2; .
To resume CD play, press • 2; again.
Insert the USB device
1 Open the cover marked on the front
panel.
2 Insert the USB device into the USB socket.»
ToThe unit starts playing from the USB
device automatically.
Insert SD/MMC card
1 Press to release the panel.
2 Insert the SD or MMC card into the card
slot.
» The unit starts playing from the SD/
MMC card automatically.
© 2008 Koninklijke Philips Electronics N.V.
All rights reserved.
Quick Start Guide_CEM220.indd 1 Quick Start Guide_CEM220.indd 1 2008-12-11 15:01:06 2008-12-11 15:01:06