Pioneer PDP-502MXE - Manual (Page 29)

Additional Information
25
<ARE1350> En
English
Specifications
General
Light emission panel ............ 50 inch plasma display panel
Number of pixels .............................................. 1280 x 768
Power supply ............................ AC 100 – 240 V, 50/60 Hz
Rated current .................................................... 5.4 – 2.2 A
Standby power consumption ................................... 0.6 W
External dimensions ........ 1218 (W) x 714 (H) x 98 (D) mm
(when using display stand)
...................................... 1218 (W) x 737 (H) x 300 (D) mm
Weight .................................................................... 40.3 kg
(including display stand) ........................................ 41.0 kg
Operating temperature range ............................ 0 to 40 °C
Operating atmospheric pressure range
........................................ 0.8 to 1.1 atmospheric pressure
Input/output
Video
INPUT 3
Input BNC jack (x5)
RGB signal (G ON SYNC compatible)
RGB ... 0.7 Vp-p/75
Ω
/no sync.
HD/CS, VD ... TTL level
/positive and negative polarity/
75
Ω
or 2.2 k
Ω
(impedance switch)
G ON SYNC ...
1 Vp-p/75
Ω
/negative sync.
INPUT 4
Input Mini D-sub 15 pin (socket connector)
RGB signal (G ON SYNC compatible)
RGB ... 0.7 Vp-p/75
Ω
/no sync.
HD/CS, VD ... TTL level
/positive and negative polarity
/2.2 k
Ω
G ON SYNC
... 1 Vp-p/75
Ω
/negative sync.
*Compatible with Microsoft’s Plug & Play
(VESA DDC1/2B)
Output Mini D-sub 15 pin (socket connector)
75
Ω
/with buffer
Audio
Input AUDIO INPUT (for INPUT3)
Pin jack (x2)
L/R ... 500mVrms/more than 10 k
Ω
AUDIO INPUT (for INPUT4)
Stereo mini jack
L/R ... 500mVrms/more than 10 k
Ω
Output AUDIO OUTPUT
Stereo mini jack
L/R ... 500mVrms (max)/less than 5 k
Ω
SPEAKER
L/R ... 8 – 16
Ω
/2W +2W (at 8
Ω
)
Control
CONTROL IN/OUT ... monaural mini jack (x2)
Accessories
Remote control unit ......................................................... 1
Remote control unit case ................................................. 1
AA (R6/UM-3) batteries .................................................... 2
Cleaning cloth ................................................................... 1
Speed clamp .................................................................... 2
Bead band ........................................................................ 2
Operating Instructions ...................................................... 1
Display stand .................................................................... 2
Washer (large) .................................................................. 2
Washer (small) ................................................................. 2
Hex hole bolt (M8X40) ..................................................... 2
÷ Due to improvements, specifications and design are subject to
change without notice.
Additional Information
CAUTION
Panel sticking and after-image
lag
• Displaying the same images such as still images for
a long time may cause after-image lagging.
This may occur in the following two cases.
1. After-image lagging due to remaining electrical load
When image patterns with very high peak luminance are
displayed for more than 1 minute, after-image lagging may
occur due to the remaining electric load. The after-images
remaining on the screen will disappear when moving
images are displayed. The time for the after-images to
disappear depends on the luminance of the still images and
the time they had been displayed.
2. After-image lagging due to sticking
Avoid displaying the same images continuously over a long
period of time with the Plasma Display. When images of
the same pattern are displayed continuously for several
hours or displayed for a short period of time every day,
after-images may remain on the screen due to the sticking
of the fluorescent materials. In this case, these images
may decrease if moving images are displayed after them,
but basically they will not disappear.