Mount the camera – Panasonic BL-C20A User Manual
Page 4
Stand/Tripod
Mounting Hole
Mounting
Screw
Position Lock
4.
Mount the camera.
The camera can be mounted in the following ways.
•
Do not mount the camera where the sun light directly hits the camera or in
outdoor-type housing without a temperature control system. The camera may
malfunction due to high temperature.
•
When you mount the camera, always hook the AC adaptor cord to the hook.
Note
Hook for
AC adaptor cord
•
This product is for indoor use only. Do not use it outdoors.
•
The camera may become warm. This is not a malfunction.
•
Mount the camera where the AC adaptor can reach an outlet, or use an
extension cord (customer-provided).
•
Do not mount the camera upside down, as the image will be displayed upside
down.
Make sure the indicator is
always in the upper right
corner.
Top
Bottom
Stand Mount
Tripod Mount
Stand/Tripod
Mounting Hole
Tripod
(customer
-provided)
Ceiling Mount
• Do not mount the camera upside down, as the image will be displayed upside
down.
• We recommend only mounting the camera using the provided hardware.
Mounting in any other manner may cause the camera to fall, resulting in
personal injury or damage to the camera.
• To reduce the load on the mounting hardware, dress the cables neatly and
secure with tape.
• Disconnect all cables from the camera. Reconnect the cables after mounting
the camera.
•
Do not mount the camera on a soft
material. The camera may fall and
be damaged.
•
Use appropriate screws for the
material of the ceiling.
Adjust the angle, then fasten the
Position Lock.
Adjust the angle, then fasten the
Position Lock.
Note
Mount the flexible stand firmly to the
ceiling with the two screws (included).
Screw
Allow sufficient space
between the wall and
the flexible stand to
turn the Position Lock.
Position Lock
Tape
(customer-provided)
Wall Mount
• Do not mount the camera upside down, as the image will be displayed upside
down.
• We recommend only mounting the camera using the provided hardware.
Mounting in any other manner may cause the camera to fall, resulting in
personal injury or damage to the camera.
• To reduce the load on the mounting hardware, dress the cables neatly and
secure with tape.
• Disconnect all cables from the camera. Reconnect the cables after mounting
the camera.
Mount the flexible stand firmly to the
wall with the two screws (included).
Screw
Allow sufficient space between the
ceiling and the flexible stand to turn
the Position Lock.
Stand/Tripod
Mounting
Hole
Indicator
Position
Lock
Mounting Screw
•
Do not mount the camera on a soft
material. The camera may fall and
be damaged.
•
Use appropriate screws for the
material of the wall.
Position Lock
Tape
(customer-provided)
Disconnect all cables from the camera. Reconnect the cables after mounting
the camera.
Note
•
Do not use a tripod screw with
a thread of 6 mm (1/4 inches)
or more. (This may damage the
Stand/Tripod mounting hole.)
•
The camera cannot be
mounted depending on the
shape of the camera platform.
Note
Connect the AC adaptor cord (and
Ethernet cable, if necessary) to the
camera and dress the cables neatly
and secure with tape (customer-
provided).
Loosen the Position Lock located on
the rear side of the flexible stand,
and turn the Mounting Screw to
attach the camera.
Loosen the Position Lock located on
the rear side of the flexible stand,
and turn the Mounting Screw to
attach the camera.
Connect the AC adaptor cord (and
Ethernet cable, if necessary) to the
camera and dress the cables neatly
and secure with tape (customer-
provided).
Note
Loosen the Position Lock located
on the rear side of the flexible
stand.
Adjust the angle, then
fasten the Position Lock.
Flexible
Stand
Stand/Tripod
Mountigng Hole
Position Lock
Mounting Screw
Turn the mounting screw to
attach the camera.