Pioneer DJm-909 - Manual (Page 18)

18
<DRB1349>
FADER OPERATIONS
Cross fader start play and back cue play
When the CH-1 CD player is held in standby at the cue point,
merely moving the cross fader lever from the right (CH-2)
side to the left (CH-1) side will cause the CH-1 CD player to
begin playback.
When the cross fader lever reaches the left (CH-1) side, CH-2
CD player performs back cue (returns to its cue point).
Likewise, when the CH-2 CD player is in standby at its cue
point, moving the cross fader lever from the left (CH-1) side
to the right (CH-2) side causes CH-2 CD player to begin
playback. When the cross fader lever reaches the right (CH-2)
side, CH-1 CD player performs back cue.
* Back cue is performed even if the input selector switch is
not set to CD.
Start playback with channel fader
1 To control a connected CD player, set the front
panel FADER START selector switch for the
corresponding channel to its [CH-1] or [CH-2]
position.
When using the CH-1 fader lever to start the CH-1 CD
player, set the front panel C.F.1/CH-1 switch to the [CH-1]
position; when using the CH-2 fader lever to start the
CH-2 CD player, set the front panel C.F.2/CH-2 switch to
[CH-2] position.
FADER START
C.F. 1 CH-1 C.F. 2 CH-2
2 Press the top panel FADER START button so that
the indicator lights.
When the CH-1 FADER START button is pressed, the
CH-1 FADER START indicator lights.
When the CH-2 FADER START button is pressed, the CH-
2 FADER START indicator lights.
3 Set the channel fader lever to the [0] scale mark.
4 Adjust the CD player to its cue point and set for
cue point standby.
5 Begin moving the channel fader lever with the
timing you wish, thereby beginning playback on
the CD player.
FADER START
REVERSE
CH-1 CH-2
REVERSE
FADER START
CH-1 FADER START CH-2 FADER START
10
9
8
7
6
5
4
3
2
1
0
10
9
8
7
6
5
4
3
2
1
0
÷ If the cue point has already been set, there is no need to
set the CD player again for standby at the cue point.
÷ After playback has once begun, moving the channel fader
lever back to the “0” scale mark will cause the CD player to
return to its cue point and enter the standby mode again
(back cue).
Start playback with cross fader
1 To control a connected CD player, set the front
panel FADER START selector switch for the
corresponding channel to its [C.F.1] or [C.F.2]
position.
When using cross fader lever to start the CH-1 CD player,
set the front panel C.F.1/CH-1 switch to the [C.F.1]
position; when using the cross fader lever to start the
CH-2 CD player, set the front panel C.F.2/CH-2 switch to
[C.F.2] position.
FADER START
C.F. 1 CH-1 C.F. 2 CH-2
2 Press the top panel FADER START button so that
the indicator lights.
When the CH-1 FADER START button is pressed, the
C.F.1 FADER START indicator lights.
When the CH-2 FADER START button is pressed, the
C.F.2 FADER START indicator lights.
3 Move the cross fader lever to the side opposite
from the channel you wish to start.
4 Adjust the CD player to its cue point and set for
cue point standby.
5 Begin moving the cross fader lever with the
timing you wish, thereby beginning playback on
the CD player.
FADER START
REVERSE
FEELING
ADJ.
C.F.1 FADER START
2 1
÷ If the cue point has already been set, there is no need to
set the CD player again for standby at the cue point.
÷ If the cross fader lever is moved fully after the beginning of
playback, the opposite channel’s CD player will return to its
cue point and enter standby there (back cue).