Document Outline

• Summary Table of Contents
• Table of Contents
• List of Figures
• List of Tables
• Compliance Information
  • Radio and TV Interference
  • Industry Canada Notice
  • FCC Part 68 (ACTA) Statement
  • CE Notice
• About this guide
  • Audience
  • Structure
  • Precautions
  • Typographical conventions used in this document
    • General conventions
    • Mouse conventions
• Chapter 1 Introduction
  • Model 3196RC iDSL T-DAC overview
  • Hardware overview
    • WAN
    • LAN
    • RS-232 control port
    • Power system
    • Central processing unit
    • iDSL ports
    • System timing
    • Temperature
    • Altitude
    • Humidity
    • Physical dimensions
    • Management services
    • LED display
  • Approvals
• Chapter 2 Hardware installation
  • Introduction
  • Unpacking the Model 3196RC T-DAC
  • T-DAC blades installation
  • Cable installation
    • Connecting the Ethernet ports
      • Connecting the 10/100Base-T Ethernet port to an Ethernet switch or hub
    • Connecting the 10/100Base-T Ethernet port to an Ethernet-capable workstation or PC
    • Connecting the EIA-561 RS-232 configuration port (DCE configured)
    • Connecting to the T1/E1 WAN ports
    • Connecting the iDSL ports
    • Connecting the BITS clock
  • Completing the hardware installation
• Chapter 3 Configuring the T-DAC for operation
  • Introduction
  • Configuration prerequisites
  • Initial configuration through the RS-232 control port
    • Connecting the DB9-RJ45 adapter with the included cable
    • Setting up the HyperTerminal (or similar program) session
  • Using a browser to complete Model 3196RC configuration
    • Displaying the T-DAC 3196RC web administration pages
      • Home page overview
    • Configuring the default gateway
    • Configuring the system clocking parameters
    • Configuring the DS0 mapping
      • Examples for configuring static connections.
    • Activating the iDSL ports
    • Configuring Patton iDSL CPE device remotely via the Model 3196RC
    • Configuring line settings and signaling for E1
      • Accessing the Line Interface Settings
    • Configuring the E1 line interface settings
    • Configuring line settings and signaling for T1
      • Accessing the Line Interface Settings
      • Configuring the T1 line settings
  • Saving your configuration
  • Backing up your configuration parameters
    • Backing up the configuration store in flash memory
  • Completing the installation
• Chapter 4 Operation and shutdown
  • Introduction
  • Activating the Model 3196RC
  • De-activating the Model 3196RC
• Chapter 5 Troubleshooting and maintenance
  • Introduction
  • Fault analysis
  • Basic iDSL and T1/E1 test modes
    • iDSL port test modes
      • Local loop
      • Remote loop
      • Line Loop
    • T1/E1 port test modes
      • DSX1 payload loop (dsx1PayloadLoop)
      • DSX1 line loop (dsxLineLoop)
  • Periodic maintenance
    • Calibration
  • Maintenance
    • Replacing the Model 3196RC
      • Exporting the current Model 3196RC configuration
      • Removing the defective Model 3196RC
      • Installing the replacement Model 3196RC
      • Importing a saved configuration
      • Completing the installation
• Chapter 6 Contacting Patton for assistance
  • Introduction
  • Contact information
  • Warranty Service and Returned Merchandise Authorizations (RMAs)
    • Warranty coverage
      • Out-of-warranty service
      • Returns for credit
      • Return for credit policy
    • RMA numbers
      • Shipping instructions
• Appendix A Network Ports (RJ-21X) connector pin-out
  • Introduction
• Appendix B WAN Network Module connector pinout
  • Introduction
  • 68-Pin Telco pinout