The radio, Normal tuning preset tuning – Panasonic RX-D21 User Manual

Page 3

Advertising
background image

RQT6744

3

1

Switch [

] to “TUNER”.

(Unit comes on.)

2

Press [BAND] to select “FM” or “AM”.

3

(Omit this step if using the remote control)

If “

” is on the display, press

[TUNE MODE] to clear it off.

4

Press [–/g] or [f/+] to
tune to the desired station.

The frequency changes one step
each time a button is pressed.

Automatic tuning
Keep [–/ g] or [f/+] depressed and release when the frequency
display starts to change. A station with good reception is automati-
cally selected and the process stops.
To stop automatic tuning, press [–/ g] or [f/+] again.

Note

Automatic tuning may stop on a frequency where there is no station if
there is interference. Press [–/ g] and [f/+] to tune if this occurs.

5

Adjust the volume.

To use auto scan
You can search for a station by listening to all tuned-in stations for 8
seconds each.
Preparation: Switch [

] to “TUNER”.

1. Press [BAND] to select “FM” or “AM”.
2. Press [AUTO SCAN].

Auto scan starts.

3. Press [AUTO SCAN] when you find the desired station.

Auto scan ends when it reaches the original frequency again.
To stop during the process, press [AUTO SCAN].

To improve reception

FM: Extend the whip antenna and adjust its direction.
AM: Adjust facing of the unit.

If noise is excessive in the FM stereo mode
Press [FM MODE]. (“

” lights up.)

Sound will be produced in monaural, but this also reduces noise.
Press the button again to cancel. (“

” goes out.)

Preset the stations (twelve FM and twelve AM) to make tuning simpler.

Preparation: Tune to the desired station.

(Do steps 14 on the left.)

1

Press [MEMORY].

2

While “

” and the frequency are

flashing

Press [MEMORY].

3

While “

” and the preset channel

are flashing

Press [–/g] or [f/+] to
select the desired channel.

(Remote control: [4

4

4

4

4] or [3

3

3

3

3])

4

Press [MEMORY].

(This completes presetting.)

Repeat the above to preset other stations.

Note

If “

” goes off during presetting, return to step 1.

1

1

1

1

1

Press [BAND] to select “FM” or “AM”.

2

(Omit this step if using the remote control)

Press [TUNE MODE] to display

”.

3

Press [–/ g] or [f/+] to select
the desired channel (1–12).

(Remote control: [4

4

4

4

4] or [3

3

3

3

3])

To use preset scan
You can search for a station by listening to all preset channels for 8
seconds each.
1. Do steps

1 to 2 above.

For remote control, replace [– / g] or [f/+] described below with [4

4

4

4

4]

or [3

3

3

3

3].

2. Press and hold [–/ g] or [f/+] until “PS” appears on the display.

3. Press [–/ g] or [f/+] when you find the desired channel.

Preset scan ends after searching through each preset channel once.
To stop during the process, press [–/ g] or [f/+].

Normal tuning

Preset tuning

The Radio

To listen to preset channels

How to preset

Indicates
auto scan

Indicates
preset scan

” lights when an FM stereo

broadcast is being received.

Preset channel

Preset channel

3 2 1

5

4

1

2

3

1 2 4

3

P3-4

11/20/02, 11:25 AM

3

Advertising
This manual is related to the following products: