Name of each part, Preparation before operation, How to operate – Panasonic CS-C9CKP User Manual

Page 2: Remote control, Indoor unit 1

Advertising
background image

NAME OF EACH PART

Remote Control

Remote Control Signal.

• Make sure it is not obstructed.
• Maximum distance : 10 m.
• Signal received sound.

One short beep or one long beep.

Notes for Remote Control.

• Do not throw or drop.
• Do not get it wet.
• Certain type of fluorescent lamps may affect

signal reception. Consult your dealer.

CHECK

TEMP

AUTO

ON

OFF

AUT

AUTO

DR

DRY FAN

AN

COOL

COOL

FAN

AUTO

RESET CLOCK

MODE

POWERFUL

QUIET

FAN SPEED

AIR SWING

OFF

CANCEL

ON

SET

1

2

3

TIMER

OFF/ON

AUTO

MANUAL

#

!

$

%
^

$

*

&

3

5

8

7

9

0

6

4

(

2

1

HEA

HEAT

How to Insert the Batteries

1

Slide down the remote control cover completely

2

Insert the batteries

– Be sure the direction is correct
– 12.00 at display - flashing
• Set the current time (CLOCK) immediately to

prevent battery exhaustion.

About the batteries

• Can be used for approximately one year.

Observe the following when replacing the

batteries
• Replace with new batteries of the same type.
• Do not use rechargeable batteries (Ni-Cd).
• Remove the batteries if the unit is not going to be

used for a long period.

1 Signal Transmitter

2 Operation Display

3 Ionizer Mode Operation Button

4 Room Temperature Setting Button

(illuminating button)

5 Operation Mode Selection Button

6 Quiet Mode Operation Button

7 Auto Airflow Direction Button

8 ON-Timer Button

9 OFF-Timer Button

0 Reset Point

(Press with fine-tipped object to clear the memory)

! OFF/ON Button

(illuminating button)

@ Powerful Mode Operation Button

# Fan Speed Selection Button

$ Manual Airflow Direction Selection Button

% Timer Set Button

^ Timer Cancellation Button

& Time-Setting Button

* Clock Button

( Remote Control Cover

CHECK

AU

TO

OF

AU

TO

HEA

T

DR

Y FA

N

COOL

FA

N

AU

TO

AU

TO

RESET

CLOCK

AIR

SW

IN

G

OF

F

CAN

CEL

1

2

3

TIM

ER

PO

WERFUL

AU

TO

MA

NU

AL

ECO

NOM

Y

SLE

ON

SE

T

FAN SPEED

MO

DE

2

1

1.5V

1.5V

PREPARATION BEFORE OPERATION

Indoor Unit

1

Connect the power supply cord to an independent
power supply

2

Open the front panel

3

Remove the air filters

4

Fit the air purifying filters in place

5

Insert the air filters

6

Close the front panel

Remote Control

– To set the current time

1

Press

1.

2

Then press

2 to increase or decrease the time.

3

Press

1 again.

Set time at display will light up.

CHECK

AUTO

AUTO HEAT

DRY FAN

COOL

FAN

AUTO

RESET CLOCK

FAN SPEED

AIR SWING

OFF

CANCEL

ON

SET

1

2

3

TIMER

AUTO

MANUAL

1

2

6

2

1

4

5

3

Setting Temperature

• Press

3 to increase or decrease the temperature.

• The temperature can be set between 16°C ~ 30°C.
• Recommended temperature:

• During AUTO Operation, press

3 to select:-

Operation with 2°C higher than the standard
temperature.

Operation with the standard temperature.

Operation with 2°C lower than the standard
temperature.

Standard Temperature

Cooling Model

• Once the Automatic Operation is selected, the indoor

temperature sensor operates automatically to select
the desired operation mode with Cooling or Soft Dry.

• After the operation mode has been selected, the

mode does not change.

Heat Pump Model

• At the beginning of the automatic operation, Heating,

Cooling or Soft Dry is automatically selected according
to the indoor temperature.

• The operation mode changes every hour, when

necessary.

Operation

Cooling

Soft Dry

Standard

temperature

25°C

22°C

Indoor

temperature

23°C

HOW TO OPERATE

To start the operation

• Press

1.

• POWER indicator (green) on the indoor unit will light

up.

• To stop, press once more.

Setting Mode

• Press

2 to select:-

Cooling Model

AUTO

– Automatic Operation

COOL

– Cooling Operation

DRY

– Soft Dry Operation

FAN

– Air Circulation Operation

Heat Pump Model

AUTO

– Automatic Operation

HEAT

– Heating Operation

COOL

– Cooling Operation

DRY

– Soft Dry Operation

Operation

Cooling

Soft Dry

Heating

Standard

temperature

25°C

22°C

21°C

Indoor

temperature

23°C

20°C

Heat Pump Model

COOL –> 26°C ~ 28°C
DRY

–> 1°C ~ 2°C

lower than the
room temperature

HEAT –> 20°C ~ 24°C

Cooling Model

COOL –> 26°C ~ 28°C
DRY

–> 1°C ~ 2°C
lower than the
room temperature

OFF

ON

HE

A

HEA

T

DR

DR

Y F

AN

AN

CO

OL

COOL

CHECK

TE

M

P

AU

T

AUT

O

AUT

O

FAN

AU

T

AUT

O

RESET

CLOCK

AIR

S

W

IN

G

OFF

CANC

EL

1

2

3

TIM

ER

OFF/

ON

AU

TO

MA

NU

AL

QU

IET

POWERFUL

ON

SE

T

FAN SPEED

MO

DE

2

3

5

1

6

4

33

CS-C7CKP CU-C7CKP5 / CS-C9CKP CU-C9CKP5 / CS-C9CKP CU-C9CKP6 / CS-C12CKP CU-C12CKP5 / CS-C12CKP CU-C12CKP6

Advertising
This manual is related to the following products: