Panasonic MR-EH57 EN - Manual (Page 47)

47
RQT8896
After performing steps 1–5 ( ➡ 46)
§ Multiple editing is possible.
After performing steps 1–7 ( ➡ 46)
§ Multiple editing is possible.
Title operations
Delete §
[HDD] [RAM] [-R] [-R]DL] [-RW‹V›]
[+R] [+R]DL] [+RW]
Press [ 2, 1] to select “Delete” and press [OK].
≥Once deleted, the recorded contents are lost and cannot be restored. Make certain before proceeding.
≥The available recording space on DVD-R, DVD-R DL, +R or +R DL does not increase when you delete titles.
≥Available recording space on DVD-RW (DVD-Video format) and +RW increases only when the last recorded
title is deleted. It does not increase if other titles are deleted.
Properties
[HDD] [RAM] [-R] [-R]DL] [-RW‹V›]
[+R] [+R]DL] [+RW] [-RW‹VR›]
Information (e.g., time and date) is shown.
≥Press [OK] to exit the screen.
Enter Name
[HDD] [RAM] [-R] [-R]DL] [-RW‹V›]
[+R] [+R]DL] [+RW]
You can give names to recorded titles.
➡ 61, Entering text
Set up Protection §
Cancel Protection §
[HDD] [RAM] [+R] [+R]DL] [+RW]
If set, this will protect the title from accidental deletion.
Press [ 2, 1] to select “Yes” and press [OK].
The lock symbol appears when the title is protected.
Partial Delete
[HDD] [RAM]
(
➡ below, For your reference)
You can remove unnecessary part of the recording.
1 Press [OK] at the start point and end point of the
section you want to delete.
2 Press [ 3, 4] to select “Finish” and press [OK].
≥Select “Next” and press [OK] to delete other sections.
3 Press [ 2, 1] to select “Delete” and press [OK].
Change Thumbnail
[HDD] [RAM] [-R] [-R]DL] [-RW‹V›]
[+R] [+R]DL] [+RW]
(
➡ below, For your reference)
You can change an image to be shown as the thumbnail picture in the Title
View.
1 Press [ 1] (PLAY) to start play.
2 Press [OK] when the image you want to use as a
thumbnail is shown.
To change the thumbnail
Restart play and press [
3, 4] to select “Change”, then press [OK] at
the point you want to change.
3 Press [ 3, 4] to select “Finish” and press [OK].
Divide Title
[HDD] [RAM]
(
➡ below, For your reference)
You can divide a title into two.
1 Press [OK] at the point you want to divide the title.
2 Press [
3, 4] to select “Finish” and press [OK].
3 Press [ 2, 1] to select “Divide” and press [OK].
To confirm the division point
Press [
3, 4] to select “Preview” and press [OK]. (The unit plays 10
seconds before and after the division point.)
To change the division point
Restart play and press [
3, 4] to select “Divide”, then press [OK] at the point where you want to divide the
title.
[Note]
≥The divided titles retain the title name and CPRM property (
➡ 84) of the original title.
≥Video and audio just before and after the dividing point may momentarily cut out.
Properties
No.
Name
Date
026
ARD
11.10.2006
Time
Rec time
12:19
0:30 (SP) MON
Dinosaur
DIRECT NAVIGATOR Title V
ARD 10.10. FRI ARD 11.10.
007 008
HDD
DIRECT NAVIGATOR Partial Delete
Start
Next
Finish
0:43.21
PLAY 008
End
- -:- -.- - - -:- -.- -
Start End
HDD
OK
RETURN
DIRECT NAVIGATOR Change Thumbnail
Change
Finish
0:00.00
- -:- -.- -
Change
HDD
008
ENTER
Start play and select the image
of a thumbnail.
DIRECT NAVIGATOR Divide Title
Preview
Finish
0:43.21
PLAY 008
Divide
- -:- -.- -
Divide
HDD
Chapter operations
Delete Chapter §
[HDD] [RAM]
Press [ 2, 1] to select “Delete” and press [OK].
≥Once deleted, the recorded contents are lost and cannot be restored. Make certain before proceeding.
≥Select “Combine Chapters” (
➡ below) when you only want to delete the division point between chapters.
(The recorded contents will not be deleted.)
Create Chapter
[HDD] [RAM]
(
➡ below, For your reference)
Select the point where you want to start a new chapter while viewing the
title.
1 Press [OK] at the point you want to divide.
≥Repeat this step to divide at other points.
2 Press [ 3, 4] to select “Finish” and press [OK].
Combine Chapters
[HDD] [RAM]
Press [ 2, 1] to select “Combine” and press [OK].
≥The selected chapter and following chapter are combined.
DIRECT NAVIGATOR Create Chapter
Create
Finish
0:43.21
PLAY 008
HDD
For your reference
≥Use search (
➡ 37), Time Slip (➡ 38) to find the desired point.
≥To find the desired point correctly, use Slow-motion ( ➡ 38) and Frame-by-frame (➡ 38).
≥To skip to the start or end of a title, press [:] (start) or [9] (end).
Ed
it
in
g
t
it
les
/c
h
a
p
ter
s
EH57_67.book Page 47 Tuesday, January 30, 2007 9:29 AM