Philips FW-P78 - Manual (Page 24)

3139 116 19452 (ENG)
24 RECORDING CLOCK
Dubbing tapes (from tape deck 1
to tape deck 2)
1 Press TAPE ( TAPE 1•2 ) to select
tape deck 2.
2 Load the prerecorded tape into tape
deck 1 with full spool to the left and
a blank tape into tape deck 2 with
full spool aside.
3 Press í or ë to select the
recording tape side (see Tape Side
under TAPE section).
4 Press DUB (HSD) once for
normal speed dubbing or twice
(within 2 seconds) for high speed
dubbing.
™ “NORMAL” (normal speed) or
“ FAST” (high speed) will be
displayed, followed by “ DUB“ with
“ < or >” scrolling left or right
depending on the tape side
selected.
™ The HSD appears on the display
during high speed dubbing.
• Dubbing will start immediately.
™ The REC starts flashing.
5 Press Ç to stop dubbing.
Notes:
– Only
е е е е е mode is available during
dubbing.
– At the end of side A, flip the tapes to
side B and repeat the procedure.
– Dubbing of tapes is only possible from
tape deck 1 to tape deck 2.
View Clock
You can view the clock (if it is set) if the
system is in Standby mode or when any
sound source is selected (CD, TUNER,
etc.). The clock will be displayed for
about seven seconds.
• Press CLOCK/TIMER briefly.
™ “PM 10:38 or 22:38 ” (the
current time) will be displayed
depending on whether you have
selected 12- or 24-hour mode.
™ “--:::::--” will be displayed if the
clock is not set.
Note:
– When the system goes into low power
standby mode, the clock setting will not
be displayed.
Clock Setting
The clock can be set in either 12- or
24-hour mode, e.g. “
AM 12:00“ or
“ 00:00“. Before setting the clock, you
must be in the View Clock mode.
1 Press CLOCK/TIMER to select
clock mode.
2 Press PROG (on the system only) to
select 12- and 24- hour mode.
™ If 12-hour mode is selected, “AM
12:00“ starts flashing.
™ If 24-hour mode is selected,
“ 00:00” starts flashing.
3 Set the hour with␣ à or á on the
system.
4 Set the minute with␣ í or ë on
the system.
5 Press CLOCK/TIMER again to
store the setting.
™ The clock starts.
SHUFFLE PROGRAM
FM
STEREO BACK HSD REPEAT REC LW MW AM T.A. NEWS
SOUND NAVIGATION
DIGITAL SOUND
CONTROL
DYNAMIC BASS
BOOST
TAPE CD
PROG
CLOCK/
TIMER NEWS!
RDS
DOLBY B NR
DUB (HSD)
REC
STANDBY
ON
SIDE A•B A.REV
TUNER AUX
PRESET ▲ ▲
STOP • CLEAR SEARCH • TUNING PLAY PAUSE PREV NEXT
MINI HIFI SYSTEM
C D 1 • 2 • 3 CDR / VIDEO FM • AM TAPE 1 • 2
TIMER FRONT
60Hz 500Hz 250Hz 1KHz 2KHz 4KHz 8KHz
VOLUME
S S
L R
C
PRO LOGIC
SIDE
– To ensure good dubbing, use tapes of
the same length.
– During high speed dubbing in Tape
mode, the sound is reduced to a low
volume.
– You can listen to another source while
dubbing.
Recording from other
sources
(only on tape deck 2)
1 Press TAPE ( TAPE 1•2 ) to select
tape deck 2.
2 Load a blank tape into tape deck 2
with the open side downward.
3 Press í or ë to select the
recording tape side (see Tape Side
under TAPE section).
4 Press CD, TUNER or AUX.
• Start playback of the selected source.
5 Press REC to start recording.
™ The REC starts flashing.
6 Press Ç to stop recording.
Notes:
– Only
е е е е е or ∂ ∂ ∂ ∂ ∂ mode is available
during recording .
– During recording, it is not possible to
listen to another source.
pg 01-28/P78/37-Eng2 12/20/99, 2:24 PM 24