NEC XM37 - Manual (Page 9)

9
7
8
8 RGB 1 (MultiCable)
RGB Input/Throughput..... Attach either end of the MultiCable to a
computer, and then attach the other end to either of these two
connectors. You can then use the remaining connector, if you
wish, to output the computer signal to a monitor. (If you do use a
second monitor, turn the monitor switch to “on.”) Either connector
can be used for input or output, however they cannot both be
used for input simultaneously. It can damage your computer.
75
Ω
/HIGH Impedance Select Switch..... This switch should be “75
Ω
”
for normal use without external termination or when your RGB
signal should be terminated with 75
Ω
. Switch to the “HIGH”
position when you have another monitor attached to your RGB
through-put connector.
9 RGB AUDIO
AUDIO R IN..... This is where you connect RGB right audio output
from a computer or another RGB source.
AUDIO L(MONO)IN..... This is where you connect RGB left audio
output from a computer or another RGB source.
AUDIO R THROUGH OUT.....Connect to a second monitor’ s
RGB right audio input.
AUDIO L THROUGH OUT.....Connect to a second monitor’s
RGB left audio input.
0 VIDEO 2
VIDEO 2 IN (BNC type)..... Connect another VCR or laser disk
player here to display the video.
S-VIDEO 2 IN..... Connect S-Video input from another external
source like a VCR.
Terminal Board
THROUGH OUT (BNC type)..... Connect to a second monitor’ s video
input to relay the video signal input at VIDEO 2 IN.
THROUGH OUT (S-VIDEO)..... Connect to a second monitor’ s S-
connector input to relay the video signal input at S-VIDEO 2 IN.
75
Ω
/HIGH Impedance Select Switch for BNC type..... Set to “75
Ω
”
during normal operation. In multiple connections using VIDEO 2
IN and THROUGH OUT (BNC type) terminals, set to “HIGH” on all
but the last monitor. Set to “75
Ω
” on the last monitor only.
AUDIO R IN..... This is your right channel audio input for stereo
sound.
AUDIO L IN (MONO)..... This is your left channel audio input for
stereo sound coming from video equipment or audio system. It
also serves as the mono audio input.
AUDIO R THROUGH OUT..... Connect to a second monitor’ s right
channel audio input.
AUDIO L THROUGH OUT..... Connect to a second monitor’ s left
channel audio input.
A VIDEO 1
VIDEO 1 IN (BNC type)..... Connect a VCR or laser disk player here
to display the video.
S-VIDEO 1 IN..... Here is where you connect S-Video input from an
external source like a VCR.
THROUGH OUT (BNC type)..... Connect to a second monitor’ s video
input to relay the video signal input at VIDEO 1 IN.
A 8 9
VIDEO 1 VIDEO 2 RGB AUDIO RGB 1
THROUGHPUT REMOTE EXTERNAL CONTROL
VIDEO RGB PROCEED
EXIT
DIP SW
AC IN
SPEAKER SELECT
EXT SPEAKER
RGB 2
AUDIO AUDIO
IN/OUT
HIGH 75 Ω
R MONO
IN
THROUGH
OUT THROUGH
OUT
IN
BNC S
HIGH 75 Ω
THROUGH
OUT
IN
R
THROUGH
OUT
IN
R
THROUGH
OUT
IN
BNC S
HIGH 75 Ω
IN
THROUGH
OUT
R G B H/CS V
HIGH 75 Ω HIGH 75 Ω
SPEAKRES MUST
HAVE MORE THAN
5WATT RATING
INPEDANCE 8 OHM
RIGHT LEFT
INT EXT
IN
THROUGH
OUT
1
2
1
2
1 2 3 4 5 6 7 8
ON
( ) L
MONO ( ) L
MONO ( ) L MONO ( ) L
0