Englis h, 6settings – National Geographic Weather Forecast 302 NE User Manual
Page 7
7
ENGLIS
H
302NE
6
Settings
6.1
Setting the country and city
After it has successfully received the Meteotime signal, the display shows in the information window ‘SELECT
COUNTRY’. After a few more minutes, the information shows the default city ‘FRANKFURTH’.
•
Press the SET - button
to switch between displaying the “cities sunrise & sunset time” or the “time & date”.
•
Press and hold the SET - button
for 3 second. ‘COUNTRY’ (LAND INST), is displayed.
•
Press the up
or down
button to select another country.
A complete list of available countries and cities can be found at the last pages of this user guide.
•
Press the SET - button
to confirm the country.
•
Press the up
or down
button to select your nearest city.
•
Press the TEST - button
to confirm. The first city will be stored.
•
Press the up
or down
button to select another city (up to 5 cities can be stored).
•
Press the TEST - button
to confirm or press the SET - button
to exit. ‘EXIT’ (INST VERL) is displayed.
6.2
Display more cities information
If you have selected more than one city:
•
Press the SET - button
repeatedly until the first city name is displayed.
•
Press the up
or down
to switch between the stored cities.
6.3
Remove the selected cities from the memory list
•
Press the SET - button
to switch between displaying the “Cities Sunrise & Sunset time” or the “Time & Date”.
•
Press and hold the SET - button
for 3 seconds. ‘COUNTRY’ (LAND INST) is displayed.
•
Press the up
or down
button to select the stored country.
•
Press the SET - button
to confirm the country.
•
Press the up
or down
button to select the stored city.
•
Press the TEST - button
to remove the city from the memory list.
•
Repeat, if necessary, to remove other cities.
•
Press the SET - button
to exit.
6.4
Personalize a place name
•
Press and hold the SET - button
for 3 second. ‘COUNTRY’ (LAND INST), is displayed.
•
Press the up
or down
button to select the stored country.
•
Press the SET - button
to confirm the country.
•
Press the up
or down
button to select the city.
•
Press the MEM - button
. A cursor flashes on the first position of the Information Window.
•
Press the up
or down
button to select a character.
•
Press the SET - button
to confirm the character and jump to the next position.
•
Press the TEST - button
to delete a wrongly entered character.
•
Press the SET - button
twice to store the new name and exit the setting.
6.5
Setting the time zone, language and display contrast
•
Press and hold the SET - button
for 3 second. ‘COUNTRY’ (LAND INST), is displayed.
•
Press the SET - button
again. The time zone ‘ZONE +00 H’ is displayed.
•
Press the up
or down
button to change the time zone.
•
Press the SET - button
to confirm. The actual display language is displayed.
•
Press the up
or down
to select one of the next display languages: German, English, Spanish, French,
Italian, Dutch or Swedish (German is the default language).
•
Press the SET - button
to confirm. The display contrast is displayed.
•
Press the up
or down
button to select the desired display contrast.
•
Press the SET - button
to confirm and exit the setting.
REMARK: If you do not have any selection into the setup mode up for 60 seconds, it will automatically exit the
setup mode.
6.6
Indoor / outdoor temperature and humidity
•
Press the IN/OUT - button
to switch between displaying the indoor or outdoor temperature and humidity
.
•
Press the MEM - button
to read the record of the maximum and minimum temperature
•
Press and hold the MEM - button
to clear the maximum and minimum temperature.
6.7
Linking the outdoor sensor with the main unit if the signal is lost
•
If the main unit cannot receive the outdoor sensor signal, the outdoor signal icon
will change to
.
•
Press and hold the IN/OUT - button
for 3 second, and then the wave icon
will flash.
•
If the signal has been received again, the outdoor signal icon
will be
.
4
4
8
7
4
8
7
10
8
7
10
4
4
8
7
4
4
8
7
4
8
7
10
4
4
8
7
4
8
7
3
8
7
4
10
4
4
4
8
7
4
8
7
4
8
7
4
24
3
3
29
29