Radio Shack 63-991 - Manual (Page 3)

3
7 5+0) "6 *' "5 6129#6%*
The stopwatch counts elapsed time up to 23
hours, 59 minutes and 59 seconds. When the
timer reaches 23:59:59, it resets to 0:00 00
and begins counting up again.
1. Repeatedly press MODE until the clock
announces “stopwatch.”
I$M7J9> I$M7J9> I$M7J9> I$M7J9>
and
&0&&ý&& &0&&ý&& &0&&ý&& &0&&ý&&
appear.
2. Press UP to start the stopwatch timer.
The stopwatch starts and announces the
elapsed time in increments shown in the
table below and the display shows the
advancing time.
For example, the stopwatch announces
“5 minutes” if
&0&+0ý&&ý &0&+0ý&&ý &0&+0ý&&ý &0&+0ý&&ý
appears.
You also can press TALK/LIGHT/SNOOZE
to hear the voice announcement at any
time while the stopwatch is running.
3. To stop counting time, press UP . The
stopwatch timer stops and the display
freezes.
4. To restart the stopwatch timer, press UP .
The stopwatch timer continues from the
elapsed time in Step 2.
5. To stop the timer, press UP then SET to
reset it to
&0&&ý&& &0&&ý&& &0&&ý&& &0&&ý&&
. The clock announces
“all clear.”
4
'%14&+0)
".
#2
"6
+/'5
The clock’s lap function lets you freeze the
display, document the timed reading, then
return to the stopwatch timer to see the
advancing time. You can monitor lap times
continuously as long as the stopwatch
continues to run.
1. Repeatedly press MODE until the clock
announces “stopwatch”. The stopwatch
display and
S.WATCH appear.
2. Press UP to start the stopwatch timer.
3. When the first lap is finished, press SET .
The stopwatch display freezes, but the
stopwatch timer continues to run.
0000
in the
elapsed time flashes.
4. When you have documented the lap
time, press SET . The display changes to
show the advancing time on the
stopwatch timer.
5. Repeat Steps 3 and 4 for each additional
lap.
6. Press UP to stop the stopwatch. Then
press SET to reset the display to
&0&&ý&& &0&&ý&& &0&&ý&& &0&&ý&&
.
The clock announces “All clear.”
4
'5'66+0)
"
6*'
"%
.1%-
If the display dims or the clock stops working
properly, use a pointed object, such as a
straightened paper clip, to press
RESET on
the back of the clock. All display segments
appear briefly, then the clock beeps twice
and 12:00 appears.
%#4'
Keep the clock dry; if it gets wet, wipe it dry
immediately. Use and store the clock only in
normal temperature environments. Handle
the clock carefully; do not drop it. Keep the
clock away from dust and dirt, and wipe it
with a damp cloth occasionally to keep it
looking new.
5
'48+%'
"
#0&
"4
'2#+4
If your clock is not performing as it should,
take it to your local RadioShack store for
assistance. Modifying or tampering with the
clock’s internal components can cause a
malfunction and might invalidate its warranty.
'NCRUGF"6KOG" "#PPQWPEGOGPV
1 to 10 seconds Each second
11 seconds to 1 minute Every 10 seconds
1 to 10 minutes Every minute
10 minutes to 24 hours Every 10 minutes
±
"016'"
±
"
• To reset the stopwatch to
&0&&ý&& &0&&ý&& &0&&ý&& &0&&ý&&
during
use, press UP then SET while the timer is
running. The clock announces “all clear” and
the timer changes to
&0&&ý&& &0&&ý&& &0&&ý&& &0&&ý&&
.
• To reset the stopwatch to
&0&&ý&& &0&&ý&& &0&&ý&& &0&&ý&&
while
recording lap times, press UP then SET
twice while
0000
flashes. The clock announces
“All clear.”
• While the stopwatch is running, you can
press MODE to use the clock’s other
features.