Roland SH-201 - Manual (Page 60)

60
Parameter list
Here’s a list of all the SH-201’s parameters.
The right column of the list (the panel operation column) shows how to set parameters that are accessible from
the panel of the SH-201 itself.
You can use SH-201 Editor (p. 56) when you want to create sounds in greater detail, or to create your own
original arpeggios.
* The values listed are the ones that appear in the screen of SH-201 Editor.
OSC MIX/MOD parameters
Parameter Value Explanation Panel operation
OSC1
WAVEFORM SAW, SQR, PW-SQR,
TRI, SIN, NOISE,
FB-OSC, SUPER-SAW,
EXT-IN Selects the waveform that is the basis of the sound. Press the WAVE buttons (p. 28)
PITCH WIDE OFF, ON Expands the range of the PITCH knob by three times. Press the WIDE button (p. 29)
PITCH -36– +36 Adjusts the pitch in semitone steps. Turn the PITCH knob (p. 29)
DETUNE -50– +50 Adjusts the pitch in one-cent steps. Turn the DETUNE knob (p. 29)
PW/FEEDBACK 0–127 • When WAVEFORM is “PW-SQR”
Specifies the width of the upper portion of the square
wave.
• When WAVEFORM is “FB-OSC”
Specifies the amount of output sound that is returned
(fed back) to the input.
• When WAVEFORM is “SUPER-SAW”
specifies the amount of pitch spread between the sev-
en sawtooth waves layered within a single oscillator.
Turn the PW/FEEDBACK knob
(p. 30)
OSC2
WAVEFORM SAW, SQR, PW-SQR,
TRI, SIN, NOISE,
FB-OSC, SUPER-SAW,
EXT-IN Selects the waveform that is the basis of the sound. Press the WAVE buttons (p. 28)
PITCH WIDE OFF, ON Expands the range of the PITCH knob by three times. Press the WIDE button (p. 29)
PITCH -36– +36 Adjusts the pitch in semitone steps. Turn the PITCH knob (p. 29)
DETUNE -50– +50 Adjusts the pitch in one-cent steps. Turn the DETUNE knob (p. 29)
PW/FEEDBACK 0–127 • When WAVEFORM is “PW-SQR”
Specifies the width of the upper portion of the square
wave.
• When WAVEFORM is “FB-OSC”
Specifies the amount of output sound that is returned
(fed back) to the input.
• When WAVEFORM is “SUPER-SAW”
specifies the amount of pitch spread between the sev-
en sawtooth waves layered within a single oscillator.
Turn the PW/FEEDBACK knob
(p. 30)
PITCH ENV
A 0–127 Specifies the time from when you play a key until the
pitch reaches the highest (or lowest) point. Move the PITCH ENV A slider
(p. 31)
D 0–127 Specifies the time from when the pitch reaches its high-
est (or lowest) point until it returns to the pitch of the key
you pressed. Move the PITCH ENV D slider
(p. 31)
OSC1 DEPTH -63– +63 Specifies the direction and amount of the OSC 1’s pitch
change. Press the OSC 1 button and then
move the PITCH ENV DEPTH
slider (p. 28, p. 31)
OSC2 DEPTH -63– +63 Specifies the direction and amount of the OSC 2’s pitch
change. Press the OSC 2 button and then
move the PITCH ENV DEPTH
slider (p. 28, p. 31)
MIX/MOD
MIX/MOD
TYPE MIX, SYNC, RING Selects how OSC 1 and OSC 2 are to be combined. Press the MIX/MOD TYPE but-
ton (p. 32)
BALANCE -63– +63 Adjusts the volume balance of OSC 1 and OSC 2. Turn the BALANCE knob (p. 33)
LOW FREQ CUT, FLAT, BOOST Selects whether the low frequency range will be boosted
or cut. Press the LOW FREQ button (p.
33)
SH-201_r_e.book 60 ページ ２００６年４月２７日 木曜日 午前１１時２８分