Recoton/Advent ARS115PSB User Manual

Placement, Subwoofer controls & connections, Connecting you subwoofer

Advertising
background image

Your Acoustic Research Subwoofer delivers powerful, deep bass sound
output for a natural, life-like sonic experience. Please follow the direc-
tions in this manual to achieve the best performance from your system.

The hook-up and operation of the Subwoofer is the same for a Home
Theater surround sound system or a stereo music system. The
Subwoofer has its own built-in amplifier, so it works with any sound
system. The Subwoofer’s own crossover network sends bass-only
signals to the Subwoofer’s built-in amplifier. This lets the Subwoofer add
extra bass to the output from your other speakers.

For simplicity, we call your Home Theater system’s or music system’s
main speakers the Front speakers. We call your AV receiver, stereo
receiver, or integrated amplifier the Receiver.

PLACEMENT

Your Acoustic Research Subwoofer must sit on the floor, in a corner to
work properly. The floor and corner are actually a part of the Subwoofer’s
design.

Place your Subwoofer in the corner nearest your system’s electronic
components to keep wire or cable runs short.

SUBWOOFER CONTROLS & CONNECTIONS

POWER CORD Plug the power cord into an
AC wall outlet or other AC outlet capable of
supplying at least 400 Watts.

POWER SWITCH Turns the AC supply com-
pletely OFF or sets the Subwoofer to AUTO ON
operation. In AUTO ON, the Subwoofer is in
standby mode until it detects an audio signal
input, then the Subwoofer turns on automati-
cally. A few minutes after audio input signals
cease, the Subwoofer automatically returns to
standby mode.

POWER INDICATOR LED This LED is unlit
when the AC power switch is OFF. It glows red
when the Subwoofer is in standby mode ad
green when the Subwoofer is on.

FUSE 250V 3A This fuse protects against
internal and external faults. If the POWER
switch is ON and the power indicator LED is
unlit, unplug the power cord from the AC
outlet and check the fuse by unscrewing the
center piece from the holder. IMPORTANT If
the fuse is blown, replace it only with a fuse of
the same type and current rating.

L, R SPEAKER-IN TERMINALS - See Connection Option 1
These terminals are for making connections using speaker wire. If you
use this option, do not use Option 2.

LINE IN - See Connection Option 2
This jack is for connection using an audio cable. If you use this option,
do not use Option 1.

LOW PASS FREQUENCY CONTROL Adjusts the upper frequency limit
for audio signals going to the Subwoofer amplifier. This control helps
you adjust the system tonal balance.

LEVEL CONTROL Balances the loudness of the Subwoofer relative to
the Front speakers and compensates for room effects on the Subwoofer’s
output.

PHASE SWITCH

The Phase Switch controls the phase of the

Subwoofer’s output relative to the front speakers. Listen carefully to the
sound quality while playing a CD with low bass. Select the position of
the switch that produces the fullest deep bass without boominess. You
may need to readjust the Level and Low Pass Frequency controls after
setting the Phase Switch.

CONNECTING YOU SUBWOOFER

IMPORTANT When you make connections. make sure that the power
switches of all components, including the Subwoofer, are OFF.

AUDIO CABLES If you are connecting the Subwoofer into a system
made up of separate components (preamp & power amps), you will need
audio cables long enough to reach the Subwoofer from the preamplifier
and the power amplifier.

SPEAKER WIRE Typical speaker wire has a pair of separate conductors
with insulating jackets that are molded together. We recommend that
you use 16-gauge speaker wire for hooking your Receiver to your Front
speakers. To make connections to the Subwoofer in parallel with the
Front speakers easier, the speaker wire connecting the Receiver to the
Subwoofer can be smaller (higher gauge number), since the Subwoofer
does not draw large amounts of power through these wires.

POLARITY All speakers in a system must be connected with the same
polarity. Speaker wire is marked for polarity so that you can identify
which wire in the pair is which. Polarity is shown by a color strip on the
insulation, by ridged molded into the insulation, or by the colors of the
wires - one copper and one silver.

Strip the insulation from speaker wire ends to reveal the bare conductors
before connecting to Receiver, Subwoofer or Speaker terminals.

IMPORTANT Always connect the red + terminal on the Receiver to the
red + terminal on the Subwoofer, and the black - terminal on the Receiver
to the black - terminal on the Subwoofer. The same is true for hooking
the Receiver outputs to the Front speakers: red + to red +, and black- to
black-.

IMPORTANT USE OPTION 1 OR OPTION 2, NOT BOTH.
OPTION 1 – CONNECTION WITH SPEAKER WIRE

Connect speaker wires from the Receiver’s front left and right speaker outputs to
the subwoofer’s left and right Speaker In terminals. Connect speaker wires from
the subwoofer’s left and right Speaker Out terminals to the left and right front
speakers being used in the system.

OPTION 2 – CONNECTION WITH AUDIO CABLE

Connect an audio cable from the Subwoofer Out or LFE Out on the back of your
Receiver to the Line In jack on the back of the subwoofer.

LEVEL

LOW PASS

FREQUENCY

• MAX

MIN •

• 100HZ

PHASE

180º

50HZ •

L

R

OUT

IN

LINE

POWER

AUTO ON

OFF

FUSE

250V T3A

120V
60HZ 300W

180º

+

+

R

L

SERIAL NO.:

MODEL NO.: ARS115PSB

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: SHOCK HAZARD-DO NOT OPEN
AVIS: RISQUE DE CHOC ELECTRIQUE-NE
PAS OUVRIR

CAUTION:
TO REDUCE THE RISK OF FIRE,
REPLACE WITH ONLY THE SAME
TYPE AND RATING OF FUSE.

ATTENTION:
UTILISER UN FUSIBLE DE
RECHANGE DE MEME TYPE.

!

IN

OUT

-

-

SPEAKER

LEVEL

SUBWOOFER ADJUSTMENT & USE

Subwoofer initial control settings

Set the LOW PASS FREQUENCY Control to its center position.

Set the LEVEL Control fully counterclockwise to MIN. You’ll reset
this control after you make other adjustments.

Adjusting the Subwoofer controls

Play a program on your system. For the following adjustments, use
the Dolby ProLogic Normal surround mode and select a movie that
has a Dolby Surround soundtrack with a lot of music, or play a music
CD. Adjust the Receiver’s volume control for a comfortable sound
level from the system speakers.

Increase the Subwoofer’s LEVEL Control setting clockwise, so that
you hear the deep bass. Adjust the control for a natural, musical
balance that has plenty of deep bass sound when it is actually
present in the music.

Listen carefully to bass voices and, if needed, adjust the LOW PASS
FREQUENCY Control so that they sound natural. Setting the
frequency too high will make deep voices sound excessively
“chesty” or resonant and will give the upper bass in music a “one-
note” quality. Setting the frequency too low will make deep voices
sound “thin” and will give music a lack of “warmth”.

Make fine adjustments until the program has satisfying and natural
sound quality on both bass voices and music.

TROUBLESHOOTING

Subwoofer POWER Indicator LED does not light

Check that the Subwoofer’s POWER Switch is in the AUTO ON position.

If the POWER Switch is in the AUTO ON position, check the AC out
let the Subwoofer is plugged into to be sure that it is live. You can
use a tester or plug-in a lamp to check it.

If the AC outlet is live, either the power cord or Subwoofer has a
problem. Unplug the power cord from the AC outlet and check the
fuse by unscrewing the center piece from the holder. If it is blown,
replace the fuse only with a fuse of the same type and rating. If this
doesn’t help, take the Subwoofer to your dealer for service – THERE
ARE NO USER SERVICEABLE PARTS INSIDE.

No sound from the Front speakers.

Be sure the Receiver and Subwoofer POWER Switches are in the On
positions.

Check the Receiver’s Volume Control Setting - if it is all the way
down, there won’t be any sound.

Check that the Receiver’s Input Selector is set to an active source of
audio signals and that a Tape Monitor Loop is not engaged.

Be sure that the Receiver’s Speaker Selector switch is turned on to
the terminals [A or B, 1or 2] that you have your Front speakers
connected to. If the Receiver has a headphone jack, you can use
headphones to check the Receiver for output.

Check the wires and connections from the Receiver’s Front Speaker
Output terminals to the Subwoofer’s SPEAKER-IN terminals.

Try removing the Subwoofer from the system, leaving your Front
speakers connected to the Receiver. If there still is no sound, take
the Receiver to your dealer for service.

No sound from the Subwoofer

First, be sure there is sound from the Front speakers and that the
Receiver is working correctly as outlined above.

Check the Subwoofer’s LEVEL Control. If it is all the way counter
clockwise, there may be no sound.

The Subwoofer only reproduces deep bass sound. If the program
has no deep bass, the Subwoofer will not make any sound. Play a
program with plenty of bass, such as jazz or rock music, or an action
movie.

If everything else checks OK, take the Subwoofer to your dealer for
service - THERE ARE NO USER SERVICEABLE PARTS INSIDE.

SPECIFICATIONS

Driver Complement and Enclosure

15” long throw woofer in a down-firing configuration.
Slot-loaded, Port Tuned enclosure design.

Frequency Response

30 Hz to 100 Hz

Amplification

Power output: 200 Watts RMS into 8 Ohms with protective limiter enabled.

Total Harmonic Distortion

1% @ 200 Watts output

Signal-to-Noise Ratio

>90 dB

Crossover frequency (-3 dB)

50 Hz @ MIN 200 Hz @ MAX

Special Features:

2 pairs 5-way gold binding posts for high level out
2 pairs 5-way gold binding posts for high level in
1 pair RCA inputs for low level input
1 pair RCA inputs for low level output

Finish: Black ash laminate

Dimensions: 16 (40.64 cm) x 19" (48.26 cm) x 19" (48.26 cm)

Weight: 66 lbs (29.94 kgs)

LIMITED WARRANTY

This warranty remains in effect for five years from the date of purchase for
speaker products and one year for electronic products.

This warranty protects the original owner providing that the product has
been purchased from an authorized Acoustic Research dealer in the United
States. The original bill of sale must be presented whenever warranty serv-
ice is required. For warranty service outside the United States, contact the
authorized Acoustic Research distributor in the country where the product
was purchased.

Except as specified below, this warranty covers all defects in material and
workmanship. The following are not covered: Damage caused by accident,
misuse, abuse, product modification or neglect, damage occurring during
shipment, damage from failure to follow instructions contained in the own-
ers manual, damage resulting from the performance of repairs by someone
no authorized by Acoustic Research, or any claims based on misrepresenta-
tions by the seller. This warranty does not cover incidental or consequen-
tial damages. It does not cover the cost of removing or reinstalling the unit.
This warranty is void if the serial number has been removed or defaced.

This warranty gives you specific legal rights. You may also have other rights
which cary from state to state. Some states do not allow the exclusion or
limitation of incidental or consequential damages or limitations on how long
an implied warranty lasts, so the above may not apply to you.

HOW TO OBTAIN SERVICE

Please call us at (800) 225-9847

We will promptly advise you of what action to take. We may direct you to
an authorized Acoustic Research Service Center or ask you to send your
speaker to the factory for repair. You will need to present the original bill of
sale to establish the date of purchase. PLEASE DO NOT SHIP YOUR
ACOUSTIC RESEARCH PRODUCT FOR REPAIR WITHOUT PRIOR
AUTHORIZATION. PLEASE DO NOT RETURN PRODUCT TO THE
ABOVE ADDRESS, IT IS NOT A SERVICE LOCATION.
You are respon-
sible for transporting your product for repair and for payment of any initial
shipping charges. However, we will pay the return shipping charges if the
repairs are covered under warranty.

RECEIVER

SUBWOOFER

SPEAKER

LEVEL

SPEAKERS

IN

OUT

+

+

+

+

+

L R

SPK OUT
L R

RECEIVER

SUBWOOFER

SPEAKER

LEVEL

SPEAKERS

IN

OUT

+

+

+

+

SPK OUT
L R

+

LFE or SUBWOOFER

LINE IN

L R

-TO BLACK TERMINAL
(plain or silver)

+TO RED TERMINAL
(color stripe ridges
or cooper)

3/8” (9mm)
BARE WIRE

Advertising