Royal Sovereign RSC-1400L - Manual (Page 10)

18 17
RSC -1400L
15. SPECIFICATIONS
Description RSC-1400L
Power supply AC 100, 200, 220~240V 50/60Hz 120V 60Hz
Power consumption 100W
Max laminating width 1400mm / 55"
Film thickness 60~500 mic / 1~15mil
Max laminating speed 5m/min / 16.4ft/min
Ready time Not applicable
Heating method None
Driving motor DC geared
Max Temperature control Not applicable
Speed control 9 settings
Transport type 2 Roller
Film core size Auto grip (2",3")
Cross cutter Yes
Hot lamination No
Cold lamination Yes
Mounting thickness 15mm / 0.6"
Take up system Chain link to main motor
Reverse Yes
Remote control Yes
Foot pedal Yes
Unit dimensions 1710 ?/X?gW.h ?V/Xf?W.Yh V/X?eW.Y?h ?V/X?W.Yhe V/T.Y?he ?S@Uhf W.R/X?he ?W.Y?V/Xhe W.Y?eV/X?h ?W.Yf?V/Xh ?.Y?gV/h
650 ?/X?gW.h ?V/Xf?W.Yh V/X?eW.Y?h ?V/X?W.Yhe V/T.Y?he ?S@Uhf W.R/X?he ?W.Y?V/Xhe W.Y?eV/X?h ?W.Yf?V/Xh ?.Y?gV/h
1210 (mm)
(w x d x h) 67.5" ?/X?gW.h ?V/Xf?W.Yh V/X?eW.Y?h ?V/X?W.Yhe V/T.Y?he ?S@Uhf W.R/X?he ?W.Y?V/Xhe W.Y?eV/X?h ?W.Yf?V/Xh ?.Y?gV/h
21.5" ?/X?gW.h ?V/Xf?W.Yh V/X?eW.Y?h ?V/X?W.Yhe V/T.Y?he ?S@Uhf W.R/X?he ?W.Y?V/Xhe W.Y?eV/X?h ?W.Yf?V/Xh ?.Y?gV/h
47.5"
Unit weight 210 kg / 462.9 bs
Carton dimensions 1960 ?/X?gW.h ?V/Xf?W.Yh V/X?eW.Y?h ?V/X?W.Yhe V/T.Y?he ?S@Uhf W.R/X?he ?W.Y?V/Xhe W.Y?eV/X?h ?W.Yf?V/Xh ?.Y?gV/h
900 ?/X?gW.h ?V/Xf?W.Yh V/X?eW.Y?h ?V/X?W.Yhe V/T.Y?he ?S@Uhf W.R/X?he ?W.Y?V/Xhe W.Y?eV/X?h ?W.Yf?V/Xh ?.Y?gV/h
850(mm)
(w x d x h) 77" ?/X?gW.h ?V/Xf?W.Yh V/X?eW.Y?h ?V/X?W.Yhe V/T.Y?he ?S@Uhf W.R/X?he ?W.Y?V/Xhe W.Y?eV/X?h ?W.Yf?V/Xh ?.Y?gV/h
35.5" ?/X?gW.h ?V/Xf?W.Yh V/X?eW.Y?h ?V/X?W.Yhe V/T.Y?he ?S@Uhf W.R/X?he ?W.Y?V/Xhe W.Y?eV/X?h ?W.Yf?V/Xh ?.Y?gV/h
33.5"
Gross Weight 292 kg / 643.7 lbs
13. MAINTENANCE
14. TROUBLESHOOTING
Cleaning the Body of the laminaor
1.To clean the machine body, dampen a cloth with water only and gently wipe the
machine clean.
Removing Adhesive Build Up
1. Remove the film from the laminator.
2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the
Teflon (metal) and silicone rollers.
Lubrication
1. Drive chain and sprockets should be lubricated with either a light coat of gear lube or
heavy grease (lithium grease) after 6 months or 1000 hours of operation, whichever
comes first.
Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the
surface.Do not use sharp metal objects, steel wool, or abrasives, as these
may also damage the rollers.
Symptom Cause Possible Solution
Machine will not turn
on:
a. Power plug is not plugged in.
b. Power switch is in “0” (Off) position.
c. Tripped circuit breaker.
d. Blown main power fuse.
a. Plug the power cord into appropriate
outlet.
b. Put the power switch to the “I” (On)
position.
c. Reset the circuit breaker.
d. Replace the fuse.
There is power, but the
rollers are not turning
after the “RUN” button
is pressed:
a. Emergency switch (es) is (are)
engaged.
b. Paper guide is not installed correctly.
c. Blown motor fuse.
a. Disengage the emergency switch (es).
b. Properly install the paper guide so that
the micro switch is activated.
d. Replace the motor fuse.
The unit is not heating
up:
a. Did not raise the temperature. a. Raise the temperature.
Curled lamination:
a. Upward curl.
b. Downward curl. a. Loosen the top roll film tension.
b. Loosen the bottom roll film tension.