Royal Sovereign RSH-1650 - Manual (Page 10)

RSS, RSR, RSH Series
18 17
15. MAINTENANCE 17. SPECIFICATIONS
16. TROUBLESHOOTING
Cleaning the Body of the lamina t or
1. To clean the machine body, dampen a cloth with water only and gently wipe the machine clean.
Removing Adhesive Build Up
1. Remove the film from the laminator.
2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the
Teflon (metal) and silicone rollers.
NOTE: Rub firmly but do not scrub the rollers vigorously as this may scratch the
surface.Do not use sharp metal objects, steel wool, or abrasives, as these may also
damage the rollers.
Problem Cause Solution
Machine will not turn
on:
a. Power plug is not plugged in.
b. Power switch is in “0” (Off) position.
c. Tripped circuit breaker.
d. Blown main power fuse.
a. Plug the power cord into appropriate
outlet.
b. Put the power switch to the “I” (On)
position.
c. Reset the circuit breaker.
d. Replace the fuse.
There is power, but the
rollers are not turning
after the “RUN” button
is pressed:
a. Emergency switch (es) is (are)
engaged.
b. Safety cover is not closed.
c. Paper guide is not installed correctly.
d. Blown motor fuse.
a. Disengage the emergency switch (es).
b. Close the safety cover to active the
safety switch.
c. Properly install the paper guide so that
the micro switch is activated.
d. Replace the motor fuse.
The unit is not heating
up:
a. The machine is in “COLD” mode.
b. Set temperature is lower than the room
temperature.
a. Switch to “HOT” mode.
b. Raise the temperature according to the
recommended film temperature.
Curled lamination:
a. Upward curl.
b. Downward curl. a. Loosen the top roll film tension.
b. Loosen the bottom roll film tension.
Unclear lamination:
a. The main roller temperatures are too
low and/or lamination speed is too fast.
a. Raise the roller temperatures and/or
lower the lamination speed.
RSS-685 / 685N
RSS-1050 / 1050N
AC 200, 220~240V
50/60Hz
2000W
3000W
685mm / 27"
1050mm / 41"
25 ~ 250mic / 1~10mil 6 m/min / 19.7 ft/min
10 min
Hot Shoe DC geared
160°C / 320°F
9 settings 4 Roller 2.25", 3"
1 Blower
2 Blower
Yes Yes Yes Yes Yes
13mm / 0.5"
Motor Yes Yes Yes
1070 x 650 x 1210 (mm)
1400 x 650 x 1210 (mm)
42" x 25.5" x 47.5"
55" x 25.5" x 47.5"
129kg / 285lbs
163kg / 360lbs
1260 x 900 x 1460 (mm)
1560 x 900 x 1460 (mm)
49.5" x 35.5" x 57.5"
61.5" x 35.5" x 57.5"
237kg / 523lbs
262kg / 578lbs
RSR-685
RSR-1050
AC 200, 220~240V
50/60Hz
2000W
300W
685mm / 27"
1050mm /41"
25 ~ 250mic / 1~10mil 4 m/min / 13.1 ft/min
15 min
Rolling Shoe DC geared
160°C / 320
°F
9 settings 4 Roller 2.25", 3"
1 Blower
2 Blower
Yes Yes Yes Yes Yes
13mm / 0.5"
Motor Yes Yes Yes
1070 x 650 x 1210 (mm)
1400 x 650 x 1210 (mm)
42" x 25.5" x 47.5"
55" x 25.5" x 47.5"
123kg / 271lbs
157kg / 346lbs
1260 x 900 x 1460 (mm)
1560 x 900 x 1460 (mm)
49.5" x 35.5" x 57.5"
61.5" x 35.5" x 57.5"
231kg / 509lbs
256kg / 565lbs
Description Power supply
Power consumption Max laminating width
Film thickness
Max laminating speed
Ready time
Heating method Driving motor
Max. temperature control
Speed control Transport type Film core size Cooling system
Side cutter Cross cutter
Film alignment Hot lamination Cold lamination
Mounting thickness
Take up system Paper counter
Length measurement
Reverse
Remote control
Foot pedal
Unit dimensions
(w x d x h) Unit weight
Carton dimensions
(w x d x h)
Carton weight
RSH-1050
RSH-1650
AC 200,220~240V
50/60Hz
3000W
3300W
1050mm / 41"
1650mm / 65"
25 ~ 250mic / 1~10mil Hot : 2 m/min / 6.6 ft/min Cold : 1 m/min / 3.3 ft/min
25 min
40 min
Hot roller DC geared
160°C / 320°F
9
settings 4 Roller 2.25", 3"
2 Blower
3 Blower
No Yes
Yes
No
Yes Yes
15(mm) / 0.6"
Motor Yes Yes Yes Yes Yes
1400 x 650 x 1210 (mm)
1960 x 650 x 1210 (mm)
55" x 25.5" x 47.5"
77" x 25.5" x 47.5"
166kg / 366lbs
269kg / 593lbs
1560 x 900 x 1460 (mm)
2190 x 900 x 1460 (mm)
61.5" x 35.5" x 57.5"
86" x 35.5" x 57.5"
265kg / 584lbs
394kg / 869lbs