Radio Shack 63-1420 - Manual (Page 2)

setting the alarm
1. Press MODE twice. The currently set alarm time
and A1 appear.
2. Hold down MODE until the alarm hour digits flash.
3. Press UP to scroll until the desired hour appears.
4. Press SET to confirm the alarm hour. The alarm
minute digits flash.
5. Press UP to scroll until the desired minute
appears.
6. Press SET to confirm the alarm minutes.
7. Press UP to toggle between A1 (alarm 1) and A2
(Alarm 2).
7. Press SET to confirm the alarm.
8. Repeat the above steps to set a second alarm
time.
viewing alarm times
1. Press MODE twice. The currently set alarm time
and A1 appear.
2. Press UP. A2 and the second alarm time appear.
If no key is pressed for 10 seconds, the display
returns to normal time mode.
activating and deactivating alarms
1. Press MODE twice. The currently set alarm time
and A1 appear.
2. Press UP to toggle between A1 and A2.
3. When desired alarm number appears, hold
down ON/OFF until the alarm icon ( W ) appears for
activation, or disappears for deactivation.
turning off the alarm
1. When the alarm sounds, press ON/OFF to turn it
off. The alarm will sound again at the set time
unless you deactivate it.
2. To temporarily silence the alarm, press SNOOZE
when the alarm sounds. The alarm sounds
again in eight minutes. Press SNOOZE again to
temporarily silence the alarm, or press ON/OFF to
turn the alarm off.
using the alarm
©2004. RadioShack Corporation.
All rights reserved. RadioShack and
RadioShack.com are trademarks
used by RadioShack Corporation.
63-1420
08A04
Printed in China
Press SNOOZE (except when the alarm is ringing), to
light the backlight for about five seconds.
view temperature and humidity
1. When in time mode, press UP repeatedly to
toggle between viewing the temperature or
humidity.
2. When the temperature appears, press SET to
toggle between Celsius and Fahrenheit degrees.
Notes:
• Temperature and humidity readings are updated
every 30 seconds.
• It takes about four minutes for the clock
to detect and display the temperature and
humidity when it is powered on.
• You cannot view the temperature or humidity
while the clock is first receiving (detecting) an
atomic clock signal.
resetting your clock
If your clock stops operating properly, press RESET
on the back of the clock.
using your clock
FCC Declaration of Conformity
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Product: Worldwide Atomic Clock
Model: 63-1420
Responsible Party: RadioShack
100 Throckmorton
Fort Worth, TX 76102
Phone: 817-415-3200
The FCC Wants You to Know
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult your local RadioShack store or an
experienced radio/TV technician for help.
If you cannot eliminate the interference, the FCC
requires that you stop using your clock.
Changes or modifications not expressly approved by
RadioShack may cause interference and void the user’s
authority to operate the equipment.
the FCC wants you to know
This product is warranted by RadioShack against manufacturing defects in material
and workmanship under normal use for one (1) year from the date of purchase from
RadioShack company-owned stores and authorized RadioShack franchisees and dealers.
For complete warranty details and exclusions, check with your local RadioShack store.
RadioShack Customer Relations
200 Taylor Street, 6th Floor, Fort Worth, TX 76102
04/04
limited one-year warranty
Q - How far into Eastern Europe is the Continental
Europe atomic clock signal detected?
A - The atomic clock at Mainflingen transmits
within an area of about 1500km radius. The
coverage area varies with weather conditions
and time of day (coverage increases up to
2500km radius at night).
Q - Is signal detection affected by physical
barriers?
A - Not usually. Long wave frequency is used for
atomic clock signal transmission, which is less
affected by physical barriers. Major barriers,
such as steel reinforced concrete, may cause
interference.
Q - How long do the batteries last?
A - Battery life depends on how often the backlight
is used, since the backlight draws a lot of
power. If the backlight is used once a day, the
batteries will last approximately 9-12 months.
Q - If you are in an area covered by two atomic
clock signals, such as Western Europe, which
signal will be received?
A - The first signal the clock receives will be used
to set the time. If this does not correspond
to your current location, you can select your
current city so the time is adjusted relative to
GMT.
frequently asked questions
Atomic Radio Signal Transmitters that can be detected:
WWVB ............................................................... Colorado (US)
DCF-77 ............................................................... Frankfurt (EU)
MSF-60 .................................................................. Rugby (UK)
JJ-40 .......................................................... Fukushima (Japan)
JJY-60 .............................................................. Kyushu (Japan)
Signal Detection Type: .................................................... TruBit
Temperature Range: ............................................. 0 ° C to 50 ° C
Temperature Resolution: ................................ ±0.1 ° C or 0.2 ° F
Humidity Range: ................................................... 30% to 90%
Humidity Accuracy: ...................................±8% at 25 ° C / 77 ° F
(humidity resolution: 1%)
specifications