Orion SIRIUS 9995 - Manual (Page 7)

7
Using the Polar Axis Finder Scope
The reticle of the polar axis finder scope for the Sirius EQ-G
has a tiny star map printed on it that makes precise polar align-
ment quick and easy. To polar align the mount using the polar
axis finder scope, follow these instructions:
1. Approximately polar-align the mount as outlined in the pro-
cedure above.
2. Loosen the Dec. lock lever and rotate the optical tube on
the declination axis until you have a clear view through
the polar axis finder scope along the right ascension axis
(Figure 8). Tighten the Dec. lock lever.
3. Focus the polar finder by rotating the eyepiece. Now, sight
Polaris in the polar axis finder scope. If you have followed
the approximate polar alignment procedure accurately,
Polaris will probably be within the field of view. If not, move
the tripod left-to-right, and adjust the latitude up-and down
until Polaris is somewhere within the field of view of the
polar axis finder scope.
Note: If you do not have a clear view of Polaris from your
observing site, you will not be able to use the polar axis finder
to precisely polar align the telescope.
4. The mount has a built-in illuminator that allows you to see
the reticle pattern in the polar axis finder scope at night.
Simply turn on the power switch on the Sirius EQ-G mount
(see “Powering the Sirius EQ-G Mount”) and the polar axis
finder scope reticle will be illuminated. Note the constel-
lation Cassiopeia and the Big Dipper in the reticle. They
do not appear in scale, but they indicate the general posi-
tions of Cassiopeia and the Big Dipper relative to the North
Celestial Pole (which is indicated by the cross at the cen-
ter of the reticle). Rotate the reticle so the constellations
depicted match their current orientation in the sky when
viewed with the naked eye. To do this, release the R.A. lock
lever and rotate the main telescope around the R.A. axis
until the reticle is oriented with sky. For larger optical tubes,
you may need to remove the tube from the mount to pre-
vent it from bumping into the mount. Once the reticle is cor-
rectly oriented, use the right ascension lock lever to secure
the mount’s position.
5. Now use the azimuth adjustment knobs (Figure 2) and the
latitude adjustment L-bolts (Figure 5) on the mount to posi-
tion the star Polaris inside the tiny circle marked “Polaris”
on the finder’s reticle. You must first loosen the knob under-
neath the equatorial mount on the center support shaft to
use the azimuth adjustment knobs. Once Polaris is properly
positioned within the reticle, you are precisely polar aligned.
Retighten the knob underneath the equatorial mount.
From this point on in your observing session, you should not
make any further adjustments in the azimuth or the latitude
of the mount, nor should you move the tripod. Doing so will
undo the polar alignment. The telescope should be moved only
about its right ascension and declination axes.
Additional Note Regarding Focusing the Polar Axis Finder
Scope
The polar axis finder scope is normally focused by simple rota-
tion of the eyepiece focus ring. However, if after adjusting the
focus ring you find that the image of the reticle is sharp, but
the stars are out of focus, then you must adjust the focus of
the polar axis finder’s objective lens. To do this, first remove
the polar axis finder from the mount by unthreading it. Look
through the polar axis finder at a star (at night) or distant object
at least 1/4 mile away (during daylight). Use the eyepiece focus
ring to bring the reticle into sharp focus. Now, loosen the focus
lock ring (Figure 7) and thread the entire objective end of the
finder inward or outward until images appear sharp. Re-tighten
the focus lock ring. Once the polar axis finder’s objective lens
is focused, it should not need to be adjusted again.
confused about Pointing the telescope?
Beginners occasionally experience some confusion about how
to point the telescope overhead or in other directions. In Figure
1 the telescope is pointed north as it would be during polar
alignment. The counterweight shaft is oriented downward. But
it will not look like that when the telescope is pointed in other
directions. Let’s say you want to view an object that is directly
overhead, at the zenith. How do you do it?
DO NOT make any adjustment to the latitude adjustment L-
bolts. That will spoil the mount’s polar alignment. Remember,
once the mount is polar aligned, the telescope should be
moved only on the R.A. and Dec. axes. To point the scope
overhead, first loosen the R.A. lock lever and rotate the tele-
scope on the right ascension axis until the counterweight shaft
is horizontal (parallel to the ground). Then loosen the Dec. lock
lever and rotate the telescope until it is pointing straight over-
head. The counterweight shaft is still horizontal. Then retighten
both lock levers.
What if you need to aim the telescope directly north, but at an
object that is nearer to the horizon than Polaris? You can’t do
Figure 9a‑d. These illustrations show the telescope pointed in the four cardinal directions. (a) north, (b) south, (c) east, (d) west. Note
that the tripod and mount have not been moved; only the telescope has been moved on the its R.A. and Dec. axes.
a. b. c. d.