Onkyo PR-SC5508 - Manual (Page 60)

60
En
Main menu Hardware Setup
Remote ID
■ Remote ID
`
1, 2, or 3
When several Onkyo components are used in the same
room, their remote ID codes may overlap. To differenti-
ate the AV controller from the other components, you
can change its remote ID from “1”, to “2” or “3”.
Note
• If you do change the AV controller’s remote ID, be sure to
change the remote controller to the same ID (see below), other-
wise, you won’t be able to control it with the remote controller.
Changing the Remote Controller’s ID
Multi Zone
See “Setting the Multi Zone” (
➔
76).
Tuner
For FM/AM tuning to work properly, you must specify the
FM/AM frequency step used in your area. Note that when
this setting is changed, all radio presets will be deleted.
■ FM/AM Frequency Step (North American
models)
` 200kHz/10kHz:
Select if 200 kHz/10 kHz steps are used in your area.
` 50kHz/9kHz:
Select if 50 kHz/9 kHz steps are used in your area.
■
AM Frequency Step (European and Asian
models)
` 10kHz:
Select if 10 kHz steps are used in your area.
`
9kHz:
Select if 9 kHz steps are used in your area.
SIRIUS Settings (North American models)
See the separate Satellite Radio Guide for more informa-
tion.
■
SAT Radio Mode
If you connect a SIRIUS Satellite Radio antenna to the
AV controller (sold separately), set this setting to “SIR-
IUS”.
■ Antenna Aiming, SIRIUS Parental Lock
These items are for use with SIRIUS Satellite Radio.
It’s not available if “SAT Radio Mode” is set to
“None”.
HDMI
■
Audio TV Out
` Off:
The audio is not output from the HDMI output.
` On:
The audio is output from the HDMI output.
This preference determines whether the incoming audio
signal is output from the HDMI output. You may want to
turn this preference on if your TV is connected to the
HDMI output and you want to listen to the audio from a
connected component through your TV’s speakers. Nor-
mally, this should be set to “Off”.
Note
• Listening mode cannot be changed when this setting is set to
“On” and the input source is not HDMI.
• If “ On ” is selected and the audio can be output from the TV, the
AV controller will output no sound through its speakers. In this
case, “TV Sp On” appears on the display.
• When “ TV Control ” is set to “ On ” , this setting is fixed to
“ Auto ” .
• With some TVs and input signals, no sound may be output even
when this setting is set to “ On ” ( ➔ 61).
• When the “Audio TV Out” setting is set to “ On ” , or “ TV Con-
trol” is set to “ On ” (
➔ 61) and you’re listening through your
TV’s speakers ( ➔ 19), if you turn up the AV controller’s volume
control, the sound will be output by the AV controller’s front left
and right speakers. To stop the AV controller’s speakers produc-
ing sound, change the settings, change your TV’s settings, or
turn down the AV controller’s volume.
• If the “Monitor Out” setting is set to “Both(Main)” or
“Both(Sub)” ( ➔ 44) and if your TV connected to a priority out-
put cannot output the audio, the sound will be heard from AV
controller’s speakers.
■
Lip Sync
` Disable:
HDMI lip sync disabled.
` Enable:
HDMI lip sync enabled.
The AV controller can be set to automatically correct any
delay between the video and the audio, based on the data
from the connected monitor.
Note
• This function works only if your HDMI-compatible TV supports
HDMI Lip Sync.
• You can check the amount of delay being applied by the HDMI
Lip Sync function on the A/V Sync screen.
• If the “Monitor Out” setting is set to “HDMI Main”,
“Both(Main)” or “Both” ( ➔ 44), the delay will be corrected in
accordance with the monitor connected to HDMI OUT MAIN.
On the other hand, if “HDMI Sub” or “Both(Sub)” is selected,
the delay will be corrected in accordance with the monitor con-
nected to HDMI OUT SUB.
Hardware Setup
1
While holding down RECEIVER, press and hold
down SETUP until RECEIVER lights (about 3
seconds).
2
Use the number buttons to enter ID 1, 2, or 3.
RECEIVER flashes twice.