Sylvania SSD800 - Manual (Page 14)

– 14 – EN
1L25
FOR TVs WITH S-VIDEO INPUT JACK
Use an S-Video cable (commercially available) in place of the yellow video cable to enjoy higher quality pic-
tures.
The S-Video connection only supplies video (picture) in the DVD mode of the DVD/VCR COMBINATION
UNITS. Therefore, in order to use the VCR features or view TV channels on the DVD/VCR COMBINATION
UNITS, you still need to either connect the RF cable to the ANT-OUT jack of the DVD/VCR COMBINATION
UNITS and the TV’s Antenna In jack, or connect the yellow video cable as described earlier (Fig.1). To connect
the supplied RF cable, see “DVD/VCR TO TV CONNECTION” above.
ANT - IN
IN
DVD/VCR
OUT
DVD/VCR
AUDIO OUT
COMPONENT
VIDEO OUT
L
L
Y
Cb
COAXIAL
S-VIDEO
OUT
DIGITAL AUDIO OUT
PCM / BITSTREAM
Cr
R
R
AUDO
VIDEO CH3 CH4
ANT - OUT
To S-VIDEO OUT jack To S-VIDEO INPUT jack
To Right (red) and Left (white)
To AUDIO OUT jacks To AUDIO INPUT jacks
A/V-compatible or
wide screen TV
[Fig. 2]
CONNECTING TO A TV THAT HAS AN
S-VIDEO INPUT JACK OR COMPONENT VIDEO IN JACKS
CONNECTING TO A TV
ANT - IN
DVD/VCR
OUT
DVD/VCR
AUDIO OUT
COMPONENT
VIDEO OUT
L
L
Y
Cb
COAXIAL
S-VIDEO
OUT
DIGITAL AUDIO OUT
PCM / BITSTREAM
Cr
R
R
AUDO
VIDEO CH3 CH4
ANT - OUT
IN
A/V-compatible or
wide screen TV
To VIDEO OUT jack To VIDEO INPUT jack
To Right (red) and Left (white)
Antenna/Cable signal
To ANT. IN
of TV
To AUDIO INPUT jacks To AUDIO OUT jacks
[Fig. 1]
Notes
¡Connect the DVD/VCR COMBINATION UNITS directly to a TV. If the A/V cables are connected to a
VCR, pictures may be distorted due to the copy protection system.
DVD/VCR TO TV CONNECTION
1. Disconnect the AC power cord of the TV from the
AC outlet.
2. Disconnect the antenna or cable from the TV.
3. Connect the antenna or cable to the ANT-IN jack of
the DVD/VCR COMBINATION UNITS.
4. Connect the DVD/VCR COMBINATION UNITS to
the TV using the RF cable.
5. Plug the AC power cords of the DVD/VCR COM-
BINATION UNITS and TV into the AC outlets.
ANT - IN
CH3 CH4
ANT - OUT
[VHF/UHF
combination antenna] [Back of the DVD/VCR]
IN OUT
[Cable box or satellite box]
OR
[Indoor antenna]
[Back of the
UHF/VHF combination TV]
UHF/VHF
RF cable
(supplied)
From Cable or
Satellite Company
OR
If your TV does not have A/V terminals:
When the DVD/VCR COMBINATION UNITS is in
the VCR Playback mode or when the DVD/VCR
COMBINATION UNITS is in the VCR mode, your TV
will receive signals from the DVD/VCR COMBINA-
TION UNITS on either channel 3 or channel 4. To use
the DVD/VCR COMBINATION UNITS with your TV,
set the selector switch to CH3 or CH4 (which is locat-
ed in the back of your
DVD/VCR COMBINATION
UNITS), whichever is not
used for normal broadcasts in
your area. Then set your TV
to the same channel.
Note to CATV system installer
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that pro-
vides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected
to the grounding system of the building, as close to the point of cable entry as practical.
ANT - IN
CH3 CH4
ANT - OUT
[Back of the DVD/VCR]
CH3 CH4
SETTING THE CH3/CH4
SWITCH
HOOKUPS
H9229UD.qxp 02.7.31 2:24 PM Page 14