Outlaw Audio 990 - Manual (Page 21)

20 Outlaw Audio
Owner’s Manual
21 Model 990 7.1 Channel Preamp/Processor
Owner’s Manual
Multi-Channel Audio If your DVD player supplies a multi-channel audio
output for DVD-Audio or SACD playback, connect the six outputs from your
player to the 7.1 AUDIO IN jack set on the rear panel of the Model 990. Use the
L, R, CEN, SUB, SL, and SR jacks; ignore the jacks labeled SBL and SBR. (These
are intended to accommodate 7.1-channel audio technology if it appears in
the future.) Be careful to match the connections—L to L, right surround to
SR, center to CEN, and so on. If your player includes a built-in Dolby Digital
decoder with 5.1-channel analog audio outputs but no DVD-A or SACD capa-
bility, we suggest that you do not use them. Use one of the Model 990’s digital
audio inputs instead—you’ll get better sound.
NOTE: You must use the 7.1 AUDIO IN multi-channel audio input for
SACD and DVD-Audio players in order to hear the high-resolution digi-
tal sound these players provide. Do not use the DVD player input.
Video Recorder
A video recording device such as a VCR, PVR (such as TiVo®, Replay®, Dish-
Player®, or similar device) or DVD recorder can be connected to the Model
990 using the following methods.
Composite Connect the composite video output from the recording device
to the VIDEO 1 IN composite video input jack on the rear of the Model 990.
Connect the recording device’s composite video input to the VIDEO 1 REC OUT
composite video jack of the Model 990.
S-Video If there is an S-Video output on the recording device, connect it to
the S-Video VIDEO 1 IN S-Video jack on the rear of the Model 990. Connect the
S-Video input to the VIDEO 1 REC OUT S-Video jack. S-Video delivers a better
picture than composite connections and should be used whenever possible,
unless you can use component or DVI connections.
Component If the recording device has a component video output, and your
TV has a component video input, connect the recording device to one of the
component video input jacks (VIDEO 1 IN, VIDEO 2 IN, or DVD IN) on the
rear of the Model 990.
DVI/HDMI If the recording device has a DVI or HDMI video output, and your
video monitor has DVI or HDMI input, connect the recording device to the
DVI-1 IN or DVI-2 IN jack on the rear of the Model 990. For HDMI-equipped
recording devices, use an HDMI-to-DVI adapter.
Analog Audio Connect the L and R audio outputs on the recorder to the VIDEO
1 IN audio jacks on the rear of the Model 990 and connect the L and R inputs
of the recorder to the VIDEO 1 REC OUT audio jacks on the Model 990.
Digital Audio If your recording device also has a digital audio output jack,
connect it one of the coaxial (COAX 1 or 2) or optical (OPT 1-4 IN) input
jacks on the rear of the Model 990, depending on the type of connector used
by the device. Later, you will configure the Model 990 to use the specific input
that you have chosen. For now, note which digital input you used on your
system chart.
If your recording device also has a digital input jack, connect it to either the
coaxial (COAX OUT) or optical (OPT OUT) output jack on the rear of the Model
990, depending on the type of connector used by the device. The signal from the
selected digital input source of the Model 990 will be sent to the recorder.
Digital TV Tuner/Cable Box/Satellite Receiver
Composite Connect the composite video output from the TV tuner to a
composite video input jack (VIDEO 1-4 IN) on the rear of the Model 990.
S-Video If there is an S-Video output on the TV tuner, and you have an S-Video
input on your TV or monitor, connect it to the S-Video input jack (VIDEO 1-4
IN) on the rear of the Model 990.
Component If the TV tuner has a component video output, and your TV has
a component video input, connect the TV tuner to one of the component input
jacks (VIDEO 1 IN, VIDEO 2 IN) on the rear of the Model 990.
DVI/HDMI If the TV tuner has a DVI or HDMI video output, and your video
monitor has DVI or HDMI input, connect the TV tuner to one of the the DVI
inputs (DVI-1 IN or DVI-2 IN) on the rear of the Model 990. For HDMI-
equipped TV tuners, use an HDMI-to-DVI adapter.
Analog Audio Connect the L and R channel outputs on the TV tuner to the
analog audio input on the rear of the Model 990 that corresponds to the video
input (VIDEO 1-4 IN) you used.
Digital Audio Connect the digital output jack on the TV tuner to one of the
coaxial (COAX 1 or 2) or optical (OPT 1-4 IN) input jacks on the rear of the
Model 990, depending on the type of connector used by the TV tuner. Later,
you will configure the Model 990 to use the specific digital audio input that
you have chosen. For now, note which digital input you connected to on
your system chart.
Video Display Connections
A video display device such as a television or a video projector can be con-
nected to the Model 990 using the following methods.
Main Zone
Composite Connect the composite video input from the display to the com-
posite (yellow) VIDEO MONITOR OUT jack on the rear of the Model 990.
S-Video If there is an S-Video input on the display, connect it to the S-Video
VIDEO MONITOR OUT jack on the rear of the Model 990.
Component If your display has a component video input, connect it to the
component video MONITOR OUT jacks on the rear of the Model 990. You should
connect this in addition to an S-Video or composite video connection.
DVI/HDMI If your video display has a DVI or HDMI video input, connect it
to the DVI OUT jack on the Model 990. If the display has only an HDMI input,
use an HDMI-to-DVI adapter.
NOTE: Because the Model 990’s on-screen display does not appear on the DVI
OUT jack, you should always use a component, S-Video, or composite video
connection in addition to the DVI connection.
Analog Audio If your TV has an internal tuner and offers an analog audio
output for its internal tuner, connect the L and R channel outputs on the
TV to an analog audio input (VIDEO 1-4 IN or AUX IN) on the rear of the
Model 990.
Connecting Your Model 990