Oreck ORBITER ORB480 - Manual (Page 8)

8
All word marks, logos, product configurations, and registered trademarks are
owned and used under the authorization of Oreck Holdings, LLC. © 2001
Oreck Holdings, LLC. All Rights Reserved. Printed in America
53303-01 REV A
08/01 ECN# R-6000
DRIVE PADS
DRIVE PAD HOLDER (Black plastic with teeth)
53178-51-0327
FLOOR PADS
POLISHING PAD (White fiber)
437051
For a higher polishing gloss use the LAMBS WOOL BONNET.
SCRUB PAD (Brown fiber)
437049
STRIP PAD (Black fiber) 437071
For all floor pads, place either DRIVE PAD HOLDER or DRIVE PAD
BRUSH on Orbiter. Then place the pad on the floor and center
Orbiter onto the pad.
FLOOR BRUSHES
SHAMPOO BRUSH (Black bristle)
237049
Use with ORECK DRY SHAMPOO (OC8). This brush has specially
cut bristles to provide safe, soft action needed for carpet cleaning.
POLISHING BRUSH - UNION MIX (Tan bristles) 237-048
This polishing brush can be used to polish wood floors. This brush
will “blend” in excess floor wax, maintain an even coat of wax
and eliminate wax buildup.
SCRUB BRUSH (Orange bristles)
237047
This brush is used to clean ceramic and concrete and many tough
stains.
GRIT BRUSH (Hard green/gray bristles)
237056
This is an extremely aggressive brush used to scour tough stains
on concrete and asphalt.
All the floor brushes snap directly onto the Orbiter with no drive
pad. Remove the brushes from the machine after use so as not to
damage them.
OTHER ACCESSORIES
LAMBS WOOL BONNET
437054
This bonnet is designed to provide the best possible shine on
wood, tile and vinyl floors. To install bonnet, place over the DRIVE
PAD HOLDER. Pull the drawstrings tight to prevent slipping. Tie a
bow and tuck the excess string inside the bonnet. After the floor
has been waxed, use the bonnet for everyday buffing to remove
scuff marks. When the bonnet becomes dirty, wash with soap and
water, wring it out and place it back on the DRIVE PAD HOLDER
to dry to its original shape.
CARPET SHAMPOO BONNET
437053
This bonnet cleans the traffic lane and spots in the carpet without
wetting the entire carpet. Use with ORECK PREMIST (Part No.
24CPTSPR) or carpet shampoo. When one side of bonnet is dirty,
flip it over and use the other side. When bonnet is completely
soiled, hose off and air dry.
SAND SCREENS
The very best in floor sanding. For all sand screens, place either
DRIVE PAD HOLDER or DRIVE PAD BRUSH on Orbiter. Then place
the sand screen under any floor pad on floor and center Orbiter
onto the pad. The SAND SCREEN comes in 60 grit (SS12060),
80 grit (SS12080), 100 grit (SS12100) and 120 grit (SS12120).
A ccessories H ard F loor C leaning
HEAVY-DUTY CLEANING FOR HARD SURFACE FLOORS
(except wood and marble)
EQUIPMENT AND MATERIALS REQUIRED:
1. Orbiter floor machine
5. Oreck O Monster ® All Purpose Cleaner
2. Black Drive Pad Holder 6. Broom or Dust Mop
3. Brown Pad
7. Cleaning Solution
4. Brush 8. Mop & Bucket
PROCEDURE:
This method uses Oreck O Monster
® All-Purpose Concentrated
Cleaner to remove dirt, grease, oil, food, shoe scuff marks, and
general grime from hard flooring. The effectiveness of the
cleaning is a direct function of the concentration of the cleaning
agent and the aggressiveness of the pad or brush being used.
1. VACUUM OR SWEEP FLOOR
Clean the floor with a broom or dust mop or Oreck vacuum
cleaner.
2. MIX CLEANING SOLUTION
Mix the Oreck All-Purpose Concentrated Cleaner with warm
water according to the directions on the bottle.
3. APPLY SOLUTION
Apply solution to floor in a 6’x6’ area. Do not flood the floor!
4. SCRUB WITH BROWN PAD OR BRUSH
Scrub floor with Orbiter using the Drive Pad Holder with the
Brown Pad or the Brush for grouted floors.
5. REMOVE SOLUTION FROM FLOOR
Pick up dirty solution with a mop or wet-dry vacuum or use
the Orbiter with a carpet bonnet to mop. Do not allow
cleaning solution to dry on floor.
6. FINISH
Rinse floor area with clean water and a clean mop. Change
water frequently.
Helpful Hints:
Clean Hard to Reach Places: Remove the center part of the
pad. Use this to scrub hard to reach areas such as corners
and around door jambs.
Do not flood the floor areas with cleaning solution.
Do not allow the cleaning solution ot dry on the floor before
pickup.
Use a clean mop for final rinse.
Change rinse water frequently.
Please check with your floor manufacturer’s remommendations
on how to clean your particular floor. Some floors require
certain procedures.