Onkyo HT-RC260 - Manual (Page 36)

36
En
■
Speaker Terminal Assign
Front High/Front Wide/Zone2
With this setting, you can specify the speakers con-
nected to FRONT HIGH OR FRONT WIDE OR
ZONE 2 SPEAKERS terminals.
` Front High:
Front high speakers can be used.
` Front Wide:
Front wide speakers can be used.
` Zone2:
Zone 2 speakers can be used (Powered Zone 2
enabled).
Note
• If the “Speakers Type” setting is set to “Bi-Amp”, Powered
Zone 2 cannot be used.
• If “Front Wide” is selected in the “SurrBack/Front High/
Front Wide” setting, you cannot select “Front Wide” here.
SurrBack/Front High/Front Wide
With this setting, you can specify the speakers con-
nected to SURR BACK OR FRONT HIGH OR
FRONT WIDE SPEAKERS terminals.
` Surr Back:
Surround back speakers can be used.
` Front High:
Front high speakers can be used.
`
Front Wide:
Front wide speakers can be used.
Note
• If the “Speakers Type” setting is set to “Bi-Amp”, Powered
Zone 2 cannot be used.
• If “Front High” is selected in the “Front High/Front Wide/
Zone2” setting, you cannot select “Front High” here.
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify “Full Band” for speakers that can output low fre-
quency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover fre-
quency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies.
■
Subwoofer
` Yes :
Select if a subwoofer is connected.
` No:
Select if no subwoofer is connected.
■
Front
` Full Band
`
40Hz to 80Hz to 100Hz, 120Hz, 150Hz, 200Hz
Note
• If the “Subwoofer” setting is set to “No”, the “Front” setting is
fixed at “Full Band”.
■
Center *1 , Surround *1 , Surr Back *2*3*4*5
` Full Band
`
40Hz to 80Hz to 100Hz, 120Hz, 150Hz, 200Hz
` None:
Select if no speaker is connected.
■
Front Wide *1*2*4*6 , Front High *1*2*4*7
` Full Band
` 40Hz to 80Hz to 100Hz, 120Hz, 150Hz, 200Hz
`
None:
Select if no speaker is connected.
Note
*1 “Full Band” can be selected only when “Full Band” is
selected in the “Front” setting.
*2 If the “Surround” setting is set to “None”, this setting cannot
be selected.
*3 If the “Surround” setting is set to anything other than “Full
Band”, “Full Band” cannot be selected here.
*4 If the “Speakers Type” setting is set to “Bi-Amp” (
➔ 35), or
Powered Zone 2 is being used (
➔ 49), this setting cannot be
selected.
*5 If you have selected other than “Surr Back” in the “Surr-
Back/Front High/Front Wide” setting, this setting cannot be
selected.
*6 If you have selected other than “Front Wide” in the “Front
High/Front Wide/Zone2” or “SurrBack/Front High/Front
Wide” setting, this setting cannot be selected.
*7 If you have selected other than “Front High” in the “Front
High/Front Wide/Zone2” or “SurrBack/Front High/Front
Wide” setting, this setting cannot be selected.
■ Surr Back Ch
` 1ch:
Select if only one surround back speaker L is con-
nected.
` 2ch:
Select if two (left and right) surround back speakers
are connected.
Note
• If the “Surr Back” setting is set to “None” (
➔ 48), this setting
cannot be selected.
■ LPF of LFE
(Low-Pass Filter for the LFE Channel)
` 80Hz, 90Hz, 100Hz, 120Hz
With this setting, you can specify the cutoff frequency
of the LFE channel’s low-pass filter (LPF), which can
be used to filter out unwanted hum. The LPF only
applies to sources that use the LFE channel.
■ Double Bass
With the Double Bass function, you can boost bass out-
put by feeding bass sounds from the front left, right, and
center channels to the subwoofer.
` On :
Double Bass function on.
` Off:
Double Bass function off.
This setting is set automatically by Audyssey 2EQ ®
Room Correction and Speaker Setup function (
➔
22).