Toshiba 34HFX83 - Manual (Page 18)

Intr
oduction
Connecting
y
our T
V
Using the
Remote Contr
ol
Setting up
y
our T
V
Using the T
V’s
F
eatur
es
Appendix
Index
18
Searching and sampling the code of a device (8500)
If you do not know the device code for a particular target unit, you
can cycle the remote control through the available codes for that
device mode and sample the functions to find the code that properly
operates the target device. The keys available to be sampled, provided
they are applicable to that mode, are POWER, 1, VOL
y, CH y, and
PLAY. Invalid keys will be ignored while in program mode.
To cycle through each available device code and sample its functions:
1. Press MODE to select the mode you want to set up.
2. While holding down the RECALL button, press 8 –5 –0 –0.
The remote control will enter program mode.
3. Point the remote control at the target device and press POWER
(or other function buttons that are available to be sampled).
4. If the device responds to the remote control:
Press RECALL to store the device code.
The mode indicator will blink twice and the remote control
will exit the program mode.
If the device does not respond to the remote control:
Press y, and then press POWER.
Repeat this step until the device responds to the remote
control, and then press RECALL.
Using the volume lock feature (8000)
For the TV, CABLE/SAT, VCR, and DVD modes, the volume controls
(VOL
yz and MUTE) can be programmed (locked) to the selected
device mode. This feature does not apply to the AUDIO1/2 modes.
For example, to lock the volume controls to always jump to the
CABLE/SAT mode:
1. Repeatedly press MODE to select the CABLE/SAT mode.
2. While holding down the RECALL button, press 8 –0 –0 –0.
3. Press VOL
y.
The Mode indicator will blink two times (locked).
The following table describes in more detail the Volume Lock
implementation.
Volume
TV CBL/SAT VCR DVD AUD1 AUD2
Locked to
TV (default) TV
TV TV TV AUD1 AUD2
CBL/SAT CBL/SAT CBL/SAT CBL/SAT CBL/SAT AUD1 AUD2
VCR VCR VCR VCR VCR AUD1 AUD2
DVD DVD DVD DVD DVD AUD1 AUD2
AUD1 AUD1 AUD1 AUD1 AUD1 AUD1 AUD1
AUD2 AUD2 AUD2 AUD2 AUD2 AUD2 AUD2
To reset the volume controls to the original device code:
1. While holding down the RECALL button, press 8 –0 –0 –0.
2. Press VOL
z.
The Mode indicator will blink four times (unlocked).
Operational feature reset (8900)
This feature clears all setup features not related to “Device code set
up” and resets the Volume Lock to “TV.”
To reset the features:
While holding down the RECALL button, press 8 –9 –0 –0.
The Mode indicator will blink two times, and then pause and
blink two more times.
TV
CABLE/SAT
VCR
DVD
AUDIO1
AUDIO2
1 2 3
4 5 6
7 8 9
100/ 0 ENT
POWER
+10
ACTION
MODE
PIC SIZE
MENU
LIGHT SLEEP
ENTER
FAV
CH VOL
EXIT
CH RTN
DVD RTN
DVD CLEAR
SLOW/DIR SKIP/SEARCH
INPUT RECALL MUTE
LIN K
THE ATE
R
FAVORITE INFO
GU IDE
SE
TU
P
TITLE SUB TITLE
AU DIO
FAV
POWER
Numbers
RECALL
MODE
y
Note:
When a search cycle is completed, the mode
indicator will blink three times. The remote
control will begin to cycle through the
available codes again. If no key is pressed
within 10 seconds while programming, the
remote control will exit the program mode
and return to the previous code.
VOL yz