Troy-Bilt 769-00425A - Manual (Page 4)

RULES FOR SAFE OPERATION
• CORD SETS: Make sure your cord set is in good
condition. When using a cord set, be sure to use a
cord that is heavy enough to carry the current that your
unit will draw. An undersized cord set will cause a drop
in line voltage resulting in loss of power and
overheating. See the operator’s manual for the unit that
will power this add-on for the recommended cord size.
• Inspect all extension cords and the unit power
connection periodically. Look closely for deterioration,
cuts or cracks in the insulation. Also inspect the
connections for damage. Replace the cords if any
defects or damage appear.
• Prevent disconnection of the straight shaft trimmer
powerhead from extension cord during operation by
using a plug-receptacle retaining strap, connector, or
by making a knot as shown below:
• Avoid dangerous environments. Never operate your unit
in damp or wet conditions. Moisture is a shock hazard.
• Do not use the unit in the rain. Do not use in or around water.
• Do not handle the plug or unit with wet hands or
standing on any wet surfaces.
• Do not leave the unit plugged in when not in use, changing
attachments or add-ons, or while being serviced.
WHILE OPERATING
• Keep bystanders, especially children and pets, at least
50 ft (15 m) away.
• Wear safety glasses or goggles that are marked as
meeting ANSI Z87.1 standards, and ear/hearing
protection when operating this unit. Wear a face or
dust mask if the operation is dusty.
• Wear heavy, long pants, boots, gloves and a long sleeve
shirt. Do not wear loose clothing, jewelry, short pants,
sandals or go barefoot. Secure hair above shoulder level.
• Use the unit only in daylight or good artificial light.
• Use the right tool. Only use this tool for the purpose intended.
• Do not force unit. It will do the job better and with less
likelihood of injury at a rate for which it was designed.
• Do not overreach, take extra care when working on steep
slopes or inclines. Always keep proper footing and balance.
• Always hold the unit with both hands when operating.
Keep a firm grip on both the front and rear handle or grips.
• Keep hands, face, and feet at a distance from all
moving parts. Do not touch or try to stop the cutting
attachment when it is rotating. Do not operate without
guards in place.
• Do not operate the engine faster than the speed
needed to do the job. Do not run the engine at high
speed when not in use.
• Always stop the engine/motor when operation is
delayed or when walking from one location to another.
.• If you strike or become entangled with a foreign object, stop
the engine/motor immediately and check for damage. Have
any damage repaired before attempting further operations.
• Stop the unit IMMEDIATELY if you feel excessive
vibration. Vibration is a sign of trouble. Inspect thoroughly
for loose nuts, bolts or damage before continuing. Repair
or replace affected parts as necessary.
• Stop and switch the unit to off for maintenance, repair,
or for changing add-ons or other attachments. The unit
must be stopped and the cutting head no longer
turning to avoid injury.
• Use only Genuine Factory Parts™ and accessories for
this unit. These are available from your authorized
service dealer. Use of any unauthorized parts or
accessories could lead to serious injury to the user or
damage to the unit, and void your warranty.
MAINTENANCE AND STORAGE
• Allow the unit to cool before storing or transporting. Be
sure to secure the unit while transporting.
• Store the unit in a locked up and dry or high and dry
place to prevent unauthorized use or damage, out of
the reach of children.
• Never douse or squirt the unit with water or any other
liquid. Keep handles dry, clean and free from debris.
Clean unit and labels with a damp sponge. Clean after
each use.
• Keep these instructions. Refer to them often and use
them to instruct other users. If you loan someone this
unit, also loan them these instructions.
• Only qualified personnel should perform any repairs
or maintenance procedures that are not described
in this manual.
• Check shear bolts, engine mounting bolts and other
bolts at frequent intervals for proper tightness to be
sure the equipment is in safe working condition.
• Inside a building store the machine away from ignition
sources. Allow the engine to cool before storing in any
enclosure.
• Always refer to the Operator’s Manual instructions for
important details if the unit is to be stored for an
extended period.
• Do not attempt to repair the machine unless you have
the proper tools, and instructions for disassembly and
repair of the machine.
SAVE THESE INSTRUCTIONS
Extension
Cord
Straight Shaft
Trimmer Cord
Straight Shaft
Trimmer Cord
Extension
Cord
4