Troy-Bilt TB26TB User Manual

Page 4

Advertising

ASSEMBLY INSTRUCTIONS

INSTALLING AND ADJUSTING THE D-HANDLE
Install
1.

Remove the screws and bottom clamp piece that were
installed on the D-handle for shipping.

Place D-handle the over the shaft housing and onto the
bottom clamp (Fig. 1). Place it a minimum of 6 inches
(15.24 cm) from the end of the shaft grip.

3. Start screws with a large Flat-head or T-25 Torx screwdriver.

Do not tighten until you make the handle adjustment.

Adjust
4.

If the D-handle was pre-installed, loosen the screws on the
handle just enough to move it.

While holding the unit in the operating position (Fig. 12, p. 7),
manuever the D-handle to the location that provides you the
best grip.

Tighten the clamp screws evenly, until the D-handle is secure.

INSTALLING TRIMMER / BLOWER ATTACHMENT
NOTE:

To make installation easier, place the unit on the

ground or on a workbench.

Turn knob counterclockwise to loosen coupler (Fig. 20).

While firmly holding trimmer attachment, push it straight
into the coupler until the release button snaps into the
primary hole (Fig. 21).

NOTE:

Aligning the release button with the guide recess will

help installation.

Turn the knob clockwise to tighten.

APPLICATIONS
•

Use the trimmer to cut grass and light weeds, and decorative
trimming around trees, fences, etc.

•

Use the blower to clean around buildings, walls, and fences
(Figs. 7 & 8), and around trees, shrubs, and flower beds (Fig. 9).

INSTALLING CUTTING ATTACHMENT SHIELD
1.

Place the narrow end of the cutting attachment shield over
the shield bracket at the back of the attachment body and
position it so that the circular cut-out slips over the guard
assembly peg (Fig. 2).

Place the locking nut
into the hexagonal hole
on the left side of the
guard and hold in place.

Insert the assembly
screw into the hole on
the right side of the
guard and screw it
into the nut on the left
side using a Phillips-
head screwdriver.

Make sure the screw
is tight before
operating the unit.

Fig. 1

(4) Screws

Shaft Grip

Shaft

Housing

On/Off Stop Control

Minimum 6 Inches

(15.24 cm)

D-Handle

Bottom Clamp

KNOW YOUR TRIMMER

SELECTING THE TRIMMER OR BLOWER
To switch between the trimmer and blower functions of this
unit, make sure that the unit is turned off and the engine has
stopped running.

To Use the Trimmer
To use the trimmer, make sure the shift handle is in the DOWN
position before starting the unit.
1. If the shift handle is in the UP

position, grasp the red shift
latch (Fig. 3) on the shift
handle and squeeze until the
internal locking mechanism
releases.

2. Push the shift handle DOWN

until the red shift latch locks
into place. DO NOT FORCE.

3. Start the unit following the

Starting Instructions (p. 6) and
the unit is ready for use.

To Use the Blower
To use the blower, make sure the
shift handle is in the UP position
before starting the unit.
1. If the shift handle is in the DOWN position, grasp the red shift

latch (Fig. 3) on the shift handle and squeeze until the internal
locking mechanism releases.

2. Pull the shift handle UP until the red shift latch locks into

place. DO NOT FORCE.

3. Start the unit following the Starting Instructions (p. 6) and the

unit is ready for use.

WARNING:

To avoid serious personal injury or

damage to the unit, DO NOT attempt to shift between
the trimmer and the blower while the unit is operating.

Fig. 3

Shift Latch

Shift Handle

Cutting

Attachment

Shield

Fuel Cap

Throttle

Control

D-Handle

Cutting Head

Shaft Grip

Primer

Bulb

Oil Plug

Spark Plug

Starter Rope Handle

Line

Cutting

Blade

Spark

Plug

Muffler

Muffler Cover

Spark Arrestor

On/Off Stop Control

Air Filter

Cover

Blower

EZ-Link

Fig. 2

Guard

Assembly

Peg

Shield

Bracket

Shift

Handle

Advertising