United States Stove Company 9947 - Manual (Page 7)

The following formula can be used to determine the maximum
heater rating per the definition of unconfined space:
BTU/HR = (L1+L2) Ft x (W) Ft x (H) Ft x 1000
50
Consider two connecting rooms with an open area between,
with the following dimensions:( See Fig. 2, Example)
L1=15-1/2 Ft., L2=12 Ft., W=12 ft., H=8Ft
50
=52800 BTU/HR
If there were a door between the two rooms the calculation would
be based only on the room with the heater.
BTU/HR=(15-1/2) x (12) x (8) x 1000
50
=29760 BTU/HR
7
FIGURE 2. FIGURE 2. FIGURE 2. FIGURE 2. FIGURE 2.
When installing the appliance directly on carpeting, tile or other combustible When installing the appliance directly on carpeting, tile or other combustible When installing the appliance directly on carpeting, tile or other combustible When installing the appliance directly on carpeting, tile or other combustible When installing the appliance directly on carpeting, tile or other combustible
material, other than wood flooring, the appliance must be installed on a
material, other than wood flooring, the appliance must be installed on a material, other than wood flooring, the appliance must be installed on a material, other than wood flooring, the appliance must be installed on a material, other than wood flooring, the appliance must be installed on a
metal or wood panel extending the full width and depth of the appliance.
metal or wood panel extending the full width and depth of the appliance. metal or wood panel extending the full width and depth of the appliance. metal or wood panel extending the full width and depth of the appliance. metal or wood panel extending the full width and depth of the appliance.
FIGURE 3. Minimum Clearances FIGURE 3. Minimum Clearances FIGURE 3. Minimum Clearances FIGURE 3. Minimum Clearances FIGURE 3. Minimum Clearances
Ensure the minimum clearances shown in FIGURE 3 are maintained for Ensure the minimum clearances shown in FIGURE 3 are maintained for Ensure the minimum clearances shown in FIGURE 3 are maintained for Ensure the minimum clearances shown in FIGURE 3 are maintained for Ensure the minimum clearances shown in FIGURE 3 are maintained for
accessibility for purposes of servicing and proper operation. Left and
accessibility for purposes of servicing and proper operation. Left and accessibility for purposes of servicing and proper operation. Left and accessibility for purposes of servicing and proper operation. Left and accessibility for purposes of servicing and proper operation. Left and
right c
right c right c right c right clearances are determined when facing the fr learances are determined when facing the fr learances are determined when facing the fr learances are determined when facing the fr learances are determined when facing the front of the heater ont of the heater ont of the heater ont of the heater ont of the heater.....
WARNINGWARNINGWARNINGWARNINGWARNING
WARNINGWARNINGWARNINGWARNINGWARNING
WARNINGWARNINGWARNINGWARNINGWARNING
Minimum clearances to
combustibles:
Top of heater...............................36"
Right Side of heater.....................15"
Left Side of heater.........................8"
Front of heater.............................42"
Rear of heater...............................4"
Maintain these clearances Maintain these clearances Maintain these clearances Maintain these clearances Maintain these clearances
to ensure adequate space
to ensure adequate space to ensure adequate space to ensure adequate space to ensure adequate space
around air opening for
around air opening for around air opening for around air opening for around air opening for
proper operation.
proper operation. proper operation. proper operation. proper operation.
If the area in which the heater may be operated is smaller than that defined as an If the area in which the heater may be operated is smaller than that defined as an If the area in which the heater may be operated is smaller than that defined as an If the area in which the heater may be operated is smaller than that defined as an If the area in which the heater may be operated is smaller than that defined as an
unconfined space or if the building is of unusually tight construction, provide
unconfined space or if the building is of unusually tight construction, provide unconfined space or if the building is of unusually tight construction, provide unconfined space or if the building is of unusually tight construction, provide unconfined space or if the building is of unusually tight construction, provide
adequate combustion and ventilation air by one of the methods described in the
adequate combustion and ventilation air by one of the methods described in the adequate combustion and ventilation air by one of the methods described in the adequate combustion and ventilation air by one of the methods described in the adequate combustion and ventilation air by one of the methods described in the
National Fuel Gas Code
National Fuel Gas Code National Fuel Gas Code National Fuel Gas Code National Fuel Gas Code,,,,, ANSI Z223.1, ANSI Z223.1, ANSI Z223.1, ANSI Z223.1, ANSI Z223.1, Section 5.3, Section 5.3, Section 5.3, Section 5.3, Section 5.3, or applicab or applicab or applicab or applicab or applicable local codes. le local codes. le local codes. le local codes. le local codes.
INSTALLATION