Viking F20347B - Manual (Page 5)

9
ELECTRICAL CONNECTION
Electrical Requirements
A 115 volt, 60 Hz, AC only 15 amp fused electrical supply is required. (A
time delay fuse or circuit breaker is recommended.) It is recommended
that a separate circuit, serving only this appliance, be provided.
•ELECTRICAL GROUND IS REQUIRED ON THIS APPLIANCE.
•DO NOT UNDER ANY CIRCUMSTANCES REMOVE THE POWER
SUPPLY CORD GROUND PLUG.
•DO NOT USE AN EXTENSION CORD
Recommended Grounding Methods
For your personal safety, this refrigerated beverage center must be
grounded. This appliance is equipped with a 7’ (2.1 m) power supply cord having a 3-prong grounding plug. To minimize
possible shock hazard, the cord must be plugged into a mating 3-prong grounding type wall receptacle grounded in
accordance with the National Electrical Code and local codes and ordinances. If the circuit does not have a grounding type
receptacle, it is the responsibility and obligation of the customer to exchange the existing receptacle in accordance with the
National Electrical Code and applicable local codes and ordinances. The third ground plug SHOULD NOT, under any
circumstances, be cut or removed. All UL listed refrigerated beverage centers are equipped with this type of plug.
Power Supply
with 3-prong
grounding plug
Grounding type wall
receptacle
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow these instructions could result
in fire or electrical shock.
LEG LEVELER INSTALLATION
Read Before Installing Leg Levelers
WARNING: Do not lay unit on top, side, back, or front. If unit is accidentally laid
in any position other than right side up, then the unit must remain in the right side
up position for at least 24 hours before plugging the unit in.
1. Tip unit backwards so there is one foot of clearance on front of the unit. Have
someone to assist you in tilting the unit to prevent it from falling on you while
installing the leg levelers.
2. Screw front two (2) leg levelers into the weldnuts. Leg levelers should be
screwed in unit snug.
3. Repeat steps 1 & 2 with the exception of tipping the unit forwards to screw in
the back two leg levelers.
4. The leg levelers are now installed.
5. The unit should be level from front to back and side to side. If floor conditions
do not allow the unit to sit level, adjust the leg leveler by turning the required
leg leveler counter-clockwise to increase the height and clockwise to reduce
the height.
Leg Leveler
(4) per unit
Weldnut
(Each bottom
corner of unit)
8
Attaching the Wood Frame to the Door (DFUR MODEL)
1. If the door is attached to the unit, remove by unscrewing the top allen head set screw at the top hinge. Remove
the door by angling the door off of the bottom hinge pin.
2. Peel back the door gasket to expose the screw holes.
3. Set the wood frame flush to the front of the door in the desired location. Clamp the wood frame to the door if
necessary.
4. Insert the wood screws through the back of the door into the pilot holes in the wood frame and tighten.
5. Reinstall the door gasket by pressing into the door channel. Make certain the corners are inserted fully.
6. Install the door to the unit. Use the supplied plastic washer as shown in the figure below.
7. Realigning the door may be necessary. Any final door adjustments can be made using a 1/8” allen head driver to
adjust the door’s hinges. (See figure below)
8. Attach the door light striker plate as shown using the 5/16” hex or phillips head screws provided. Make certain the
light is able to turn on and off when the door is opened and closed.
9. Attach the door to the unit by reversing step number 1 above.
Magnetic door
gasket
Rear of Door
Bottom of door Attached wood frame
3/8” clearance
holes for
frame wood
screws -
10 holes
1/8” allen head screws for hinge
adjustment
Door hinge
adjustment screws
Door light striker plate
Attaching the Handle
Attach the handle of your choice by drilling mountingholes through panel. Countersink or counterbore holes from back
side of panle for handle screw heads to be flush
CAUTION
Door can become
disengaged if washers
are not installed.
CAUTION
Door can become
disengaged if
washers are not
installed.
Cabinet
Hinge
Wood
Frame
Door Hinge
Door Hinge
Shoulder bushing
3/4” OD x 7/16”
ID Washer
3/4” OD x 1/4” ID
Washer
(3) Nylon hardware
components at
bottom hinge
CAUTION
Door may not swing properly
if all nylon components are
not installed as shown
Bottom Hinge Cover
Wood Frame
Hinge Hardware Installation
Details
5/8”x 7/32” ID washer
Shoulder
bushing
(2) Nylon
hardware
components at
top hinge
Top Hinge Cover