Vision Fitness R2700HRT - Manual (Page 3)

2 STEP
• Slide the console mast boot onto the
console mast.
• Unfold the wire harness and heart
rate wires located in the console mast
frame bracket. Attach the wire tie
coming from the bottom of the console
mast to the wire harness and heart
rate wires. Pull the wire tie with wire
harness and heart rate wires up
through the top of the console mast
while simultaneously sliding the mast
into the frame bracket.
• Secure the console mast to the
frame bracket with six lock washers
(M8) and six bolts (M8x15L). Tighten
with the 5mm T-shaped wrench. Place
the seventh bolt (M8x15L) in the rear of
the frame bracket and tighten until snug.
• Slide the console mast boot down
and snap it into place on the side cover.
BLUE BAG
3 STEP
• Mount the upper handlebars to the
console mast using two lock washers
(M8) and two bolts (M8x15L). Tighten
with the 5mm T-shaped wrench.
• Remove the four mounting bolts from
the back of the console. Connect the
wire harness and heart rate wires that
run through the console mast into the
plugs located in the back of the console.
Attach the console to the mast with the
four bolts removed earlier.
• Remove the battery cover on the
backside of the console. Plug in the
9-volt battery. Re-attach the battery cover.
PINK BAG
1 STEP
• Install the rear foot with the four
lock washers (M8), two inside bolts
(M8x65L), and two outside bolts
(M8x20L). Tighten with the 5mm
T-shaped wrench.
ORANGE BAG
A s s e m b l y
G u i d e
R2700HRT
COMMERCIAL FITNESS BIKE
1 STEP
4 STEP
• Attach the seat frame to the sliding
seat bracket using four lock washers
(M8) and four socket head bolts
(M8x20L) and the 6mm T-shaped
wrench.
• Connect Wires A on the seat
handlebar to Wires B on the sliding
seat bracket. Attach the seat
handlebars to the sliding seat bracket
using four lock washers (M8) and four
bolts (M8x15L). Tighten with the 5mm
T-shaped wrench.
GREEN BAG
2 STEP
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order.
Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in
your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble
your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts
and screws are in place and partially threaded in before completely tightening any ONE bolt or screw.
5 STEP
4 STEP
5 STEP
• Secure the Lumbar controlled seat
back and the seat bottom to the seat
frame with eight lock washers (M6)
and eight bolts (M6x55L). Tighten
with the 4mm L-shaped wrench.
• Snap the plastic seat cover into
place on the back of the lumbar
controlled seat.
BLACK BAG
3 STEP
Wires B
Wires A
6 STEP
• Attach the left and right pedals to the
left and right crank arms. Tighten the
pedals using the 15mm pedal wrench.
• Secure the accessory tray to the seat
handlebar with two bolts (M5x35L)
and two lock washers (M5). Tighten
with the screwdriver.
YELLOW BAG
6 STEP
Lumbar Controlled
Seat Back
Seat Bottom
Console Mast
Handlebar
Seat Handlebar
Seat Frame
Console Mast
Console Mast
Boot
Frame
Bracket
Rear Foot
Accessor y
Tray
Pedal
Plastic Seat
Cover
Sliding Seat
Bracket