Vector Start-It VEC020 - Manual (Page 8)

Figure 1
WARNING: Automotive lead-acid batteries can generate hydrogen gas during normal
operation. More gas is generated when the battery is charging. Hydrogen
gas is: • Explosive • Poisonous to Breathe • Highly Flammable
To avoid an explosion and/or the possibility of being splashed with battery acid:
• NEVER allow the red and black clamps to touch each other or a common metal object
• ONLY attempt to jumpstart a vehicle, boat or engine system in a WELL ventilated area
• ALWAYS CONNECT THE RED (+) CLAMP TO THE POSITIVE (+) BATTERY
TERMINAL FIRST
• DO NOT CONNECT THE BLACK (–) CLAMP TO THE NEGATIVE (–) BATTERY
TERMINAL
• DO CONNECT THE BLACK (–) CLAMP TO A NON-MOVING METAL PART ON
THE ENGINE
CAUTIONS:
I. To avoid possible damage that may shorten the unit’s working life, protect this unit
from direct sunlight, direct heat, and/or moisture.
2. This system is to be used ONLY on vehicles, boats, garden tractors and gasoline
powered generators with 12 volt DC battery systems.
3. This system is NOT designed to be installed as a replacement for a vehicular battery.
RECOMMENDATIONS FOR OPTIMUM PERFORMANCE OF THE START-IT
Compact Pro
™ JUMPSTART SYSTEM:
WARNING: Never insert anything other than the supplied power/recharging cords or
recommended appliance power/recharging cords into the charging or
power receptacles on this unit.
IMPORTANT: The Safety ON/OFF Switch should be in the OFF position
when the unit is charging, or not in use.
3. USING THE START-IT Compact Pro™ AS A JUMPSTART SYSTEM
WARNINGS:
1. Before using this system to jump start any vehicle or boat, read and understand all
instructions, safety tips, warnings and cautions and first aid information provided in
this manual and on the product labeling. Additional important information may also
be provided by the vehicle‘s battery system manufacturer.
2. Be aware of first aid procedures before attempting jumpstart procedure.
3. ALWAYS wear protective eyewear when working with a lead acid-type battery.
Safety Switch
Worklight
ON/OFF
Switch
Red LEDs
Full Green LED
Battery Status Pushbutton
Negative Battery
Clamp
12 Volt Accessory Socket (DC Recharge)
Worklight AC/DC Recharge Port
Positive Battery
Clamp
• DO NOT smoke or use inflammable items (matches, cigarette lighters, etc.) while
working on a vehicle’s battery system
• When using this jumpstarter in proximity to the vehicle‘s battery and engine, stand the
unit on a flat, stable surface, and be sure to keep all cords and cables well away from
any moving parts
• Check unit periodically for wear and tear. Replace worn or defective parts immediately
- contact Vector ® Customer Service Department at (954) 584-4446 ext. 19 or through
our internet address: www.vectormfg.com
• Do not attempt to jumpstart a frozen battery
• NEVER submerge this unit in water
• Do not wear vinyl clothing when jumpstarting a vehicle; friction can cause dangerous
static electricity sparks. Remove all jewelry or metal objects; they can cause short cir-
cuits or react with battery acid to cause severe burns. Remove or secure any loose
clothing items and restrain long hair, before attempting jumpstart procedure
CAUTIONS:
• Vehicles that have on-board computerized systems may be damaged if vehicle battery
is jumpstarted. Before jumpstarting this type of vehicle, read the vehicle’s owner’s
manual to confirm that external starting assistance is advised.
• Excessive engine cranking can damage the vehicle‘s starter motor. If the engine fails
to start after the recommended number of attempts, discontinue jumpstart procedure
and look for other problems that may need to be corrected.
3.1 EASY, STEP-BY-STEP JUMPSTARTING INSTRUCTIONS
1. Turn OFF vehicle ignition and all accessories (radio, a/c, lights, cell phone, etc.).
Place vehicle in “park” and set the emergency brake.
2. Make sure jumpstart system’s Safety Switch is turned OFF.
3. Remove the booster clamps from protective holster (fig. 2): simply squeeze the handles
and pull down on the clamp.
Follow procedure for negative or positive
grounded system, as follows:
NEGATIVE GROUNDED SYSTEM
(NEGATIVE BATTERY TERMINAL IS
CONNECTED TO CHASSIS
MOST
COMMON METHOD
4. Connect positive (+) red clamp to vehicle battery‘s positive terminal.
5. Connect negative (-) black clamp to chassis or a solid, non-moving, metal vehicle
component or body part. Never clamp directly to negative battery terminal or moving
part. If the audible alarm sounds, the polarity is not correct. Reverse the connections.
DO NOT TURN ON THE SAFETY SWITCH WITH ALARM SOUNDING.
SLIDE DOWN AND ROTATE CLAMP OUTWARD
FROM SIDE OF UNIT TO REMOVE
Clamp
Handle
8 9
Figure 2