Installation instructions – Whynter UIM-155 User Manual
Page 4
INSTALLATION INSTRUCTIONS
¾ BEFORE USING YOUR ICE MAKER
• REMOVE
THE
EXTERIOR
AND
INTERIOR
PACKAGING
MATERIAL.
• CHECK
TO
BE
SURE
YOU
HAVE
ALL
OF
THE
FOLLOWING
PARTS:
• 1
ICE
BUCKET
• 1
PLASTIC
SCOOP
• 25
FT.
HOSE
• 1
INSTRUCTION
MANUAL
• BEFORE
CONNECTING
THE
ICE
MAKER
TO
THE
POWER
SOURCE,
LET
IT
STAND
UPRIGHT
FOR
APPROXIMATELY
4
HOURS.
THIS
WILL
REDUCE
THE
POSSIBILITY
OF
A
MALFUNCTION
IN
THE
COOLING
SYSTEM
FROM
HANDLING
DURING
TRANSPORTATION.
• CLEAN
THE
INTERIOR
SURFACE
WITH
LUKEWARM
WATER
USING
A
SOFT
CLOTH.
¾ INSTALLATION OF YOUR ICE MAKER
• THIS APPLIANCE IS DESIGNED TO BE RECESSED OR BUILT-IN (FULLY RECESSED).
• PLACE
YOUR
ICE
MAKER
ON
A
HARD
AND
LEVEL
FLOOR
THAT
IS
STRONG
ENOUGH
TO
SUPPORT
THE
ICE
MAKER
WHEN
IT
IS
FULLY
LOADED.
REMEMBER
THAT
THE
UNIT
WILL
BE
SIGNIFICANTLY
HEAVIER
ONCE
IT
IS
FULLY
LOADED.
TO
LEVEL
YOUR
ICE
MAKER,
ADJUST
THE
LEG
AT
THE
FRONT
OF
THE
ICE
MAKER.
• PLACE
THE
ICE
MAKER
AWAY
FROM
DIRECT
SUNLIGHT
AND
SOURCES
OF
HEAT
(STOVE,
HEATER,
RADIATOR,
ETC.).
DIRECT
SUNLIGHT
MAY
AFFECT
THE
ACRYLIC
COATING
AND
HEAT
SOURCES
MAY
INCREASE
ELECTRICAL
CONSUMPTION.
EXTREME
COLD
AMBIENT
TEMPERATURES
MAY
ALSO
CAUSE
THE
ICE
MAKER
NOT
TO
PERFORM
PROPERLY.
• AVOID
LOCATING
THE
ICE
MAKER
IN
DAMP
AND
HUMID
AREAS.
TOO
MUCH
HUMIDITY
IN
THE
AIR
WILL
CAUSE
FROST
TO
FORM
QUICKLY
ON
THE
EVAPORATOR
REQUIRING
MORE
FREQUENT
DEFROSTING
OF
THE
ICE
MAKER.
• PLUG
THE
ICE
MAKER
INTO
AN
EXCLUSIVE
PROPERLY
INSTALLED-GROUNDED
WALL
OUTLET.
DO
NOT
UNDER
ANY
CIRCUMSTANCES
CUT
OR
REMOVE
THE
THIRD
(GROUND)
PRONG
FROM
THE
POWER
CORD.
ANY
QUESTIONS
CONCERNING
POWER
AND
OR
GROUNDING
SHOULD
BE
DIRECTED
TOWARD
A
QUALIFIED
ELECTRICIAN.
¾ ELECTRICAL CONNECTION
• THIS
ICE
MAKER
SHOULD
BE
PROPERLY
GROUNDED
FOR
YOUR
SAFETY.
THE
POWER
CORD
OF
THIS
ICE
MAKER
IS
EQUIPPED
WITH
A
THREE-PRONG
PLUG
WHICH
IS
USED
WITH
STANDARD
THREE
PRONG
WALL
OUTLETS
TO
MINIMIZE
THE
POSSIBILITY
OF
ELECTRICAL
MALFUNCTION.
• DO
NOT
UNDER
ANY
CIRCUMSTANCES
CUT
OR
REMOVE
THE
THIRD
GROUND
PRONG
FROM
THE
POWER
CORD
SUPPLIED.
• DO
NOT
USE
AN
EXTENSION
CORD
TO
CONNECT
POWER
TO
THE
UNIT.
• NEVER
USE
A
TWO-PRONG
GROUNDING
ADAPTER.
• WHERE
A
TWO-PRONG
WALL
RECEPTACLE
IS
ENCOUNTERED,
CONTACT
A
QUALIFIED
ELECTRICIAN
TO
HAVE
IT
REPLACED
WITH
A
3-PRONG
RECEPTACLE
IN
ACCORDANCE
WITH
APPLICABLE
ELECTRICAL
CODES.
• THIS
ICE
MAKER
REQUIRES
A
STANDARD
115/120
VOLTS
A.C.~/60HZ
ELECTRICAL
OUTLET
WITH
THREE-PRONG
GROUND.
• THE
CORD
SHOULD
BE
SECURED
BEHIND
THE
ICE
MAKER
AND
NOT
LEFT
EXPOSED
OR
DANGLING
TO
PREVENT
ACCIDENTAL
INJURY.
a
WARNING
a
IMPROPER USE OF THE GROUNDED PLUG CAN RESULT IN THE RISK OF ELECTRICAL
SHOCK. IF THE POWER CORD IS DAMAGED, DO NOT ATTEMPT ANY REPAIRS. ORDER A
REPLACEMENT FROM YOUR WHYNTER RETAILER AND HAVE A QUALIFIED ELECTRICIAN
REPLACE THE POWER CORD