Wagan IMPACT DRIVER - IMPACT WRENCH 2257 - Manual (Page 4)

Impact Wrench Kit by Wagan Tech
USER’S MANUAL — Please read before using this equipment.
________________________________________________________________________________________________________________________________________________________________
www.wagan.com
© 2004 Wagan Corporation.
All Rights Reserved.
Wagan and Wagan.com are trademarks used by Wagan Corporation.
4
5. Remove the vehicle’s spare tire and set it aside.
6. Use the vehicle’s jack to raise the vehicle. CAUTION! Refer to
the vehicle manufacturer’s owner’s manual for instructions on using
the jack and to determine the proper lifting points on the vehicle.
Always chock the opposite wheel.
7. If necessary, remove the wheel’s hubcap to expose the wheel lug
nuts.
8. Make sure the Impact Wrench is off. Then, depress the Forward/
Reverse Switch to its Reverse position (counterclockwise rotation).
9. Insert the Socket onto the first wheel lug nut and, while
maintaining a firm grip on the Impact Wrench with both hands,
squeeze the Trigger until the wheel lug nut is removed from the
wheel lug bolt. Release pressure on the Trigger to turn the Impact
Wrench off. Remove the wheel lug nut from the Socket and set the
lug nut aside. Then, repeat this Step to remove the remaining wheel
lug nuts.
10. Once all of the wheel lug nuts are removed, carefully remove the
vehicle’s flat tire and install the spare tire onto the wheel lug bolts.
11. Finger tighten each of the wheel lug nuts onto the wheel lug
bolts.
12. Make sure the Impact Wrench is off. Then, depress the
Forward/ Reverse Switch to its Forward position (clockwise rotation).
13. Note: Check vehicle owner’s manual for tightening sequence.
Insert the Socket onto the first wheel lug nut and, while maintaining a
firm grip on the Impact Wrench with both hands, squeeze the Trigger
until the wheel lug nut is firmly tightened onto the wheel lug bolt.
Release pressure on the Trigger to turn the Impact Wrench off.
Then, repeat this Step to tighten the remaining wheel lug nuts onto
the lug bolts.
14. Using the vehicle’s jack, slowly and carefully lower the vehicle.
15. If necessary, re-attach the vehicle’s hubcap to the wheel. Then,
store the vehicle’s jack and spare tire securely in the trunk of the
vehicle.
16. If the vehicle’s battery was used to supply electricity to the
Impact Wrench, disconnect the Red and Black Battery Clamps from
the battery. Disconnect the Lead Wire Plug from the Battery
Clamps. Remove the Socket from the Impact Wrench. Place the Impact Wrench and its accessories in the Carrying Case. Then, store the
Carrying Case securely in the vehicle’s trunk.
17. If the vehicle’s cigarette lighter receptacle was used to supply
electricity to the Impact Wrench, disconnect the Lead Wire Plug from the
cigarette lighter receptacle. Insert the cigarette lighter back into its
receptacle. Remove the Socket from the Impact Wrench. Place the Impact
Wrench and its accessories in the Carrying Case. Then, store the Carrying
Case securely in the vehicle’s trunk.
INSPECTION, MAINTENANCE, AND CLEANING :
1. Before each use, inspect the general condition of the Impact Wrench.
Check for loose connections, cracked, or broken parts, excessively worn or
damaged wiring, and any other condition that may affect the safe and
proper operation of the Impact Wrench. If a problem occurs, have the
problem corrected before further use. Do not use damaged equipment.
2. When cleaning, use only water and a mild detergent. Do not immerse
the Impact Wrench in liquid. Do not use cleaners that are combustible or
corrosive.
PRODUCT SPECIFICATIONS :
Name Description
Electrical Requirements 12 Volt DC / 4.5 Amps
Fuse 13 Amp
Torque Capacity
155 lbf-ft (~ 210 N.m) Clockwise
250 lbf-ft (~ 340 N.m) Counterclockwise
Drive Socket Sizes
0.67in, 0.75in, 0.83in, 0.91in
(17mm 19mm 21mm 23mm)
Cords
DC Cord/Plug for Cigarette Lighter Receptacle
Alligator Cord/Clamps for Battery Terminal
Light Built-In LED Light For Night Use