Wibur Curtis Company SD2 - Manual (Page 3)

Number of
Blinks
170ºF
172ºF
174ºF
176ºF
178ºF
180ºF
182ºF
184ºF
186ºF
188ºF
190ºF
192ºF
194ºF
196ºF
198ºF
200ºF
202ºF
204ºF 1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Temperature
Temperature Settings
Confirm/Reset Confirm/Reset Confirm/Reset Confirm/Reset Confirm/Reset TTTTTempera empera empera empera emperature ture ture ture ture
Manual Liquid Dispensing Mode Manual Liquid Dispensing Mode Manual Liquid Dispensing Mode Manual Liquid Dispensing Mode Manual Liquid Dispensing Mode
This feature sets up the SD2 unit to dispense coffee only as long as the user holds down the selected PUSH button.
As soon as the user stops pressing the button, coffee stops flowing into the cup. Setting the unit for Manual Liquid Dispense will turn off the
Portion Control Dispense Mode.
Enter Program Mode – Enter Program Mode – Enter Program Mode – Enter Program Mode – Enter Program Mode – press and hold STOP/W STOP/W STOP/W STOP/W STOP/WASH ASH ASH ASH ASH for about ten [10] seconds until all lights on the control panel
are blinking.
Set Manual Dispense – Set Manual Dispense – Set Manual Dispense – Set Manual Dispense – Set Manual Dispense – While you are in the programming mode, press and hold the PUSH button.
Hot liquid will start to flow.
Continue to hold down the PUSH button until liquid stops
stops stops stops stops flowing, then release the button.
At this time, you have selected the Manual Liquid Dispensing Mode and have exited out of the programming mode.
Enter
Program Mode
Select Manual
Liquid Dispense
Stop & Exit
TTTTTo Confirm o Confirm o Confirm o Confirm o Confirm TTTTTempera empera empera empera emperature. ture. ture. ture. ture. Press and hold STOP/WASH button for approximately 2-3 seconds. When the READY light
starts blinking. Lift off from STOP/WASH button. Each blink equals 2ºF, starting with 170ºF, to a maximum of 204ºF.
These features allow you to check the heating tank temperature or change the temperature if desired. The temperature in the tank is
programmable from 170°F, in 2 degree increments up to 204°F .
Enter Enter Enter Enter Enter TTTTTempera empera empera empera emperature Program Mode. ture Program Mode. ture Program Mode. ture Program Mode. ture Program Mode. Press and hold STOP/WASH button. READY light will
start “quick flashing”.
TTTTTo Change o Change o Change o Change o Change TTTTTempera empera empera empera emperature. ture. ture. ture. ture. Continue holding STOP/WASH button. Each quick flash equals
2ºF. Release STOP/WASH when desired temperature is reached.
TTTTTo Set and Exit, o Set and Exit, o Set and Exit, o Set and Exit, o Set and Exit, press either of the PUSH buttons.
Enter
Temp. Program
Change
Tank Temp.
Set & Exit
TTTTTo Change o Change o Change o Change o Change TTTTTank ank ank ank ank TTTTTempera empera empera empera emperature ture ture ture ture
Programming Continued ...
3
LOW LOW LOW LOW LOW TEMPERA TEMPERA TEMPERA TEMPERA TEMPERATURE LOCKOUT (DEL TURE LOCKOUT (DEL TURE LOCKOUT (DEL TURE LOCKOUT (DEL TURE LOCKOUT (DELTTTTTA): A): A): A): A): This mode will give you a choice of two minimum operating temperatures. Delta one allows you to operate
the unit at a temperature as low as 195º F. Delta two will allow you to dispense at a temperature as low as 185º F. Delta three does not limit the minimum
operating temperature. The Cafe system comes from the factory with a Delta three setting. To make adjustments enter Program Mode:
1. Press and hold Stop/Wash button, until all lights on the control panel are blinking, about 10 seconds. Release button.
2. While in the Program Mode, press and hold Stop/Wash button the READY light will begin blinking, continue to hold the Stop/Wash button. The READY
light will stop blinking. Continue holding Stop/Wash button until the READY light comes back on in a longer, 3 second glow.
3. Now release the Stop/Wash button The READY light will now blink a pattern of flashes indicating current delta setting.
DELTA ONE (one long glow, followed by one blink) allows you to run the coffee dispense at five degree below maximum.
DELTA TWO (one long and two blinks) allows you to run the coffee dispense at 15 degrees below maximum.
DELTA THREE (one long and three blinks) allows you to operate the unit at any temperature.
4. To change the setting, press and hold the Stop/Wash button for about three seconds until you receive a short flash. Release the button and you will
add one blink to the delta pattern or continue holding to add two blinks.
5. To set press any other button. The unit will return to normal operation with the new delta lockout setting.