weber 41894 User Manual

Page 6

Advertising
background image

pg6

START/
HI

4).

OFF

3).

1).

2).

6).

2).

5).

1).

2).

6).

2).

5).

5).

OFF

3).

START/
HI

4).

To Extinguish

Push in and turn burner control
knob clockwise to the OFF
position.

ƽ CAUTION do not

fold in tables until grill is cold.

ƽ DANGER

Do not use an open flame to check for
gas leaks. Be sure there are no sparks

or open flames in the area while you

check for leaks. Sparks or flames will

result in a fire or explosion which can

cause serious bodily injury or death, and

damage to property.

ƽ DANGER

Do not store a spare LP-gas cylinder under or near this
appliance. Never fill the cylinder beyond 80 percent
full. If the instructions are not followed exactly, a fire
causing death or serious injury may occur.

ƽ DANGER

Failure to open the lid while igniting the grill’s burner, or not waiting 5 minutes to allow
the gas to clear if the grill does not light, may result in an explosive flame-up which
can cause serious bodily injury or death.

Manual Lighting

1) Open the lid.

2) Unfold the work surfaces.

3) Make sure the burner control knob

is turned OFF.

ƽ WARNING: Do not lean over

the open grill. Keep your face
and body at least one foot away
from the matchlight hole when
lighting the grill.

4) Turn the cylinder on by turning the

cylinder valve counterclockwise.

5) Strike a match and put the flame

into the matchlight hole under
the igniter.

6) Push burner control knob down

and turn to START/HI.

7) Check that the burner is lit by

looking down through the cooking
grate. You should see a flame.

ƽ WARNING: If the burner does

not light, turn the burner control
knob to OFF and wait 5 minutes
to let the gas clear before you
try again or try to light with a
match.

Lighting

Summary lighting instructions
are on the fold out work surface.

1) Open the lid.

2) Unfold the work surfaces.

3) Make sure the control knob

is turned OFF. (Push control
knob in and turn clockwise to

ensure that it is in the OFF
position.)

ƽ WARNING: Do

not lean over the open grill.
Keep your face and body at
least one foot away from the
matchlight hole when lighting
the grill.

4) Push burner control knob

down and turn to START/HI.

5) Push the red ignition button

several times, so it clicks
each time.

6) Check that the burner is lit

by looking down through the
cooking grate. You should see
a flame.

ƽ WARNING: If the

burner does not light, turn
the burner control knob to
OFF and wait 5 minutes to
let the gas clear before you
try again or try to light with
a match.

1)

1 ).

Attach Propane Cylinder
Use propane cylinders with a capacity of 14.1
oz or less. Use propane cylinders that are
approximately 3" inches in diameter and 11"
inches in length. The propane cylinder must fit
through the cylinder support ring (1).
ƽ CAUTION: Use cylinders that are marked

“Propane fuel” only.

Note: Your Weber

®

gas grill is equipped with

a cylinder supply system designed for vapor
withdrawal.
Slide propane cylinder through support ring (1).
While holding carrying handle closest to propane
cylinder with one hand, push propane cylinder into
regulator and turn clockwise until tight.

ƽ WARNING: Do not use a wrench to tighten

the connection. Using a wrench could
damage the regulator coupling and could
cause a leak.

Check for gas leaks:
1) Regulator to propane cylinder connection.
ƽ WARNING: If there is a leak at connection

(1), remove propane cylinder. Do not
operate grill. Use a different propane
cylinder and recheck for leaks with soap
and water solution. If a leak persists after
retightening the propane cylinder, turn OFF
the gas. DO NOT OPERATE
THE GRILL.

Contact the Customer Service Representative
in your area using the contact information on
our web site. Log onto www.weber.com

®

.

2) Valve to-regulator connections.
ƽ WARNING: If there is a leak at connection

(2) turn OFF the gas. DO NOT OPERATE
THE GRILL. Contact the Customer Service
Representative in your area using the
contact information on our web site. Log
onto www.weber.com

®

.

When leak checks are complete, turn gas
supply OFF at the source and rinse connections
with water.

Advertising