Yamaha HTR-5590 - Manual (Page 51)

47
English
INTR
ODUCTION
PREP
ARA
TION
B
ASIC OPERA-
TION
AD
V
ANCED
OPERA
TION
ADDITIONAL
INFORMA
TION
APPENDIX
REMOTE CONTROL FEATURES
4 Press the button for which you want to
program the new function.
“LEARN” is displayed.
5 Press and hold the button on the other
remote control that has the function you
want to program into this remote control
until “OK” appears in the display window.
Notes
• “NG” appears in the display window when programming has
not been done correctly. In this case, start over from step 4.
• This remote control can learn approximately 120 functions.
However depending on the signals learned, “FULL” may
appear in the display window much earlier than this number. In
this case, clear unnecessary programmed functions to make
further learning on the remote control.
6 Repeat steps 4 and 5 to program additional
functions.
7 Press LEARN again to exit from the learning
mode.
Notes
• Learning may not be possibe in the following cases:
– when the batteries in the remote control for this unit or other
components are weak
– when the distance between the two remote controls is too
much or too little
– when the remote control infrared windows are not facing at
the appropriate angle
– when the remote control is exposed to the direct sunlight
– when the function to be programmed is continuous or
uncommon
• “ERROR” appears in the display window when pressing
buttons other than indicated in each step.
Learn Feature
If you want to program functions not included in the basic
operations covered by the manufacturer code, or a
manufacturer code is not available, the following
procedure needs to be performed. The possible
programming area is the same as a component control
area, so the buttons are programmable independently for
each source component area.
Note
• This remote control transmits infrared rays. If the other remote
control also uses infrared rays, this remote control can learn
most of the other remote control’s functions. However, you
may not be able to program some special signals or extremely
long transmissions. (Refer to the operation instructions for the
other remote control.)
■ Programming a new remote
control function
1 Press an input selector button or A to
select a source component.
2 Place this remote control and the other
remote control 1 to 4 cm apart on a flat
surface so that their infrared transmitters are
aimed at each other.
3 Press LEARN by using a ballpoint pen or
similar object.
Do not press and hold LEARN longer than three
seconds. Otherwise this unit enters the manufacturer
code setting mode.
Notes
• Complete each of the following steps in 30 seconds. Otherwise,
the learning mode will be automatically canceled. In this case,
press LEARN again.
• Do not press and hold LEARN longer than 3 seconds.
Otherwise this unit enters the manufacturer code setting mode.
A
PHONO
POWER
SLEEP
CLEAR
LEARN
ST ANDBY
TRANSMIT
RE –NAME
6CH INPUT
SYSTEM V -AUX
D -TV/LD POWER REC DISC SKIP
AUDIO
VOL
POWER
AMP
AV
TV
VCR2/DVR
VCR 1
D VD
SELECT
CBL/SA
T
MD/T
APE
CD-R
TUNER
CD + –
1 to 4 cm (approximately 1 inch)
A
PHONO
POWER
SLEEP
CLEAR
LEARN
ST ANDBY
TRANSMIT
RE –NAME
6CH INPUT
SYSTEM V -AUX
D -TV/LD POWER
POWER
AMP
AV
TV
VCR2/DVR
VCR 1
DVD SELECT
CBL/SA
T
MD/T
APE
CD-R
TUNER
CD
A PHONO
POWER SLEEP STANDBY 6CH INPUT
SYSTEM
V-AUX
D-TV/LD VCR2/DVR VCR 1 DVD
CBL/SAT MD/TAPE CD-R
TUNER CD
LEARN
Flashes alternately
LEARN
A
PHONO
POWER
SLEEP
CLEAR
LEARN
ST ANDBY
TRANSMIT
RE –NAME
6CH INPUT
SYSTEM V -AUX
D -TV/LD POWER
POWER
AMP
AV
TV
VCR2/DVR
VCR 1
DVD SELECT
CBL/SA
T
MD/T
APE
CD-R
TUNER
CD
0108HTR5590_44-54_EN(U) 02.8.5, 4:31 PM 47