X10 Wireless Technology VK68A - Manual (Page 2)

The KR28A Remote Control sends Wireless Radio
Frequency (RF) signals to the VS10A. It is normally set to
Housecode A and controls cameras connected to channels
1 thru 8. You can however change the Housecode:
To change the Housecode for the KR28A remote
1. Press and hold the number 1 button. The red LED blinks
once. 3 seconds later, the LED blinks the current setting:
1 blink for Housecode A, 2 blinks for B....... 16 blinks
for P.
2. Release the number 1 button.
3. Press and release the number 1 button the appropriate
number of times for the Housecode you want to set.
Once for A, twice for B, etc. The LED blinks for each
press. IMPORTANT: Hold the button on your last press.
3 seconds later, the red LED blinks back the new setting,
e.g. 3 blinks for Housecode C. If you do not follow this
programming sequence, the LED will stay on for 1 second
and your existing setting will not be changed.
Note: if you change the Housecode setting for the remote
you must reprogram the VS10A to recognize it. To do this
just set the group of cameras that the VS10A will scan as
described in “Changing the group of cameras you want to
scan” earlier. When you press a button on the KR28A to
set the group, the VS10A will automatically be set to
recognize the new housecode setting for the KR28A.
To change the batteries: Pry the unit apart and fit two
CR2016 Lithium 3V batteries. Observe polarity.
VK68A-11/01
Page 2 of 2
X10.com, a division of X10 Wireless Technology, Inc.
For more info please visit: www.x10.com/support
Press and release to
scan forward (short
delay between
images displayed).
Press and
release to scan
backward (short
delay between
images dis-
played). Press
any # to stop
scan and display
that camera.
Press to turn on
cameras 1 thru 8
FCC CAUTION: THIS DEVICE COMPLIES WITH PART 15
OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
NOTE: Modifications to any of the components in this kit will
void the user’s authority to operate this equipment.
LIMITED 1-YEAR WARRANTY
X10.com, a division of X10 Wireless Technology, Inc. (X10)
warrants X10 products to be free from defective material and
workmanship for a period of one (1) year from the original date of
purchase at retail. X10 agrees to repair or replace, at it’s sole
discretion, a defective X10 product if returned to X10 within the
warranty period and with proof of purchase.
If service is required under this warranty:
1. Call 1-800-675-3044 or visit www.x10.com, or e-mail
[email protected] to obtain a return merchandise authoriza-
tion (RMA) number.
2. Return the defective unit postage prepaid to X10 (see
address on back).
3. Enclose a check for $4.00 to cover postage and handling.
4. Enclose a dated proof of purchase.
5. X10 is not responsible for shipping damage. Units to be
returned should be packed carefully.
Please visit www.x10.com/warranty
to complete your on-line warranty registration. Thank you.
Computer Control
Connect the VS10A’s Serial IN RCA jack to your PC’s
serial port using the RS-232 to RCA cable (supplied). Install
the software from the link you received in the e-mail you
got confirming your order. You need to be connected to
the Internet while you install it. Follow the installation
instructions and refer to the software’s Help section. Set
the COM port setting for the serial port you connected the
VS10A to. You will now be able to control your Anaconda
cameras from your PC.
The PC software also lets you disable the RF control
section of the VS10A if you desire, to prevent anyone from
being able to control your cameras by remote control.