Yamaha DSP-Z9 - Manual (Page 97)

95
English
ZONE 2
A
D
V
ANCED
OPERA
T
ION
3
Press an input selector button to select the
input source you want to listen to in the
second room.
The display window shows “2: name of selected
input”.
Signals input to V-AUX and PHONO jacks cannot be sent to
Zone 2.
4
You can control this unit from Zone 2 using
the input selector, STANDBY, SYSTEM
POWER, MUTE and VOLUME +/– buttons.
* VOLUME +/– can only be used when Variable is selected
in Zone 2 Volume (see page 78). Further, you cannot
adjust the volume of signals output from ZONE 2
COAXIAL OUT.
5
Press SOURCE SELECT k / n to exit from the
Zone 2 mode.
• The source in Zone 2 and the source available for recording are
always the same.
• “Zone 2” appears in the display window only when k is
pressed, and SYSTEM only when n is pressed.
■ Turning this unit to either on or standby
SYSTEM POWER and STANDBY work differently
depending on the selected mode that appears on the
display window.
• When the Normal or Zone2 mode is selected, you can
turn the main unit or Zone 2 to on/standby individually.
• When the System mode is selected, or when YPC is
selected as the amplifier library (L:AMP) code, you
can turn the main unit and Zone 2 to on/standby
simultaneously.
* “MAIN” appears for a few seconds when SYSTEM POWER
or STANDBY is pressed.
■ Special considerations for DTS software
The DTS signal is a digital bitstream. If you attempt to
send the DTS signal to the second room you will only hear
digital noise (that may damage your speakers). Thus, the
following considerations and adjustments need to be made
when playing DTS encoded discs.
For LDs or DVDs encoded with DTS
Only 2 channel analog audio signals may be sent to the
second/third room.
• for LDs: Set your LD player’s left and right outputs to
the analog soundtrack.
• for DVDs: Use the disc menu to set the DVD player’s
mixed 2-channel left and right audio outputs to the
PCM or Dolby Digital soundtrack.
For CDs encoded in DTS
To avoid unexpected noise, DO NOT USE the Zone 2
feature with CDs encoded in DTS.
Note
Notes
TUNER PHONO
CD
DVD DVR VCR 2 DTV/LD VCR 1
CD-R MD/TAPE SAT CABLE
V-AUX
*
TRANSMIT RE-NAME
STANDBY TUNER
MULTI CH IN PURE DIRECT
TOP EXIT INPUT MODE SOUND
SYSTEM
CLEAR LEARN MACRO OFF ON MACRO
PHONO
CD
DVD DVR VCR 2
TITLE
MENU
CHAPTER
PAUSE STOP POWER REC
STEREO AMP 10KEY HALL CHURCH JAZZ
SELECT
DISPLAY
SEARCH
SOURCE
PLAY
– +
ENTER
DTV/LD VCR 1
CD-R MD/TAPE SAT CABLE
POWER V-AUX
STEREO
6.1/5.1
AMP 10KEY
JAZZ
MOVIE THX
MUTE VOLUME
STRAIGHT
TV INPUT TV VOL CH
PRESET
DISC EFFECT
TV MUTE
MUSIC ENTERTAIN ROCK
HALL 1 HALL 2 CHURCH
NIGHT /DTS
CHP/INDEX
A/B/C/D/E
1
5
9
6
0 +10 +100
7 8
2 3 4
PUSH
LCD display SYSTEM POWER/
STANDBY
Normal mode* Name of component Turns the main unit
to on/standby
Zone 2 mode “Zone 2” or “2:name
of component” Turns Zone 2 to on/
standby
SYSTEM mode “SYSTM” Turns everything (the
main unit and Zone
2) to on/standby
00EN.00_DSPZ9_GB.book Page 95 Thursday, November 13, 2003 10:55 AM