Milwaukee V18 PD - Manual (Page 10)

18 19
V18 DD V18 PD
...........................13 mm ..........................13 mm
...........................38 mm ..........................38 mm
..............................- ................................16 mm
...........................12 mm ..........................12 mm
......................0-500 /min .....................0-500 /min
....................0-1600 /min ...................0-1600 /min
...........................32 Nm ...........................32 Nm
...........................71 Nm ...........................71 Nm
......................47/19 Nm ......................47/19 Nm
.............................500 ...............................500
.............................500 ...............................500
.............................660 ...............................660
...........................18 V ..............................18 V
.....................1,5-13 mm ....................1,5-13 mm
..........................2,6 kg ............................2,6 kg
...........................73 dB (A) ......................89 dB(A)
...........................84 dB (A) ....................100 dB(A)
.......................< 2,5 m/s 2 .........................4,5 m/s 2
ENGLISH ENGLISH
TECHNICAL DATA
Drilling capacity in steel ........................................................................
Drilling capacity in wood .......................................................................
Drilling capacity in brick and tile ...........................................................
Wood screws (without pre-drilling) .......................................................
No-load speed ......................................................................................
1st gear .............................................................................................
2nd gear .............................................................................................
Torque
Low torque*1 .....................................................................................
High torque*1 .....................................................................................
Static jamming moment, 1st gear/2nd gear *1 .................................
Screwing capacity with one fully charged battery (3,0 Ah) : *2
5x40 Soft wood .................................................................................
Drilling capacity with one fully charged battery (3,0 Ah):
ø 3 mm Steel plate 1,6 mm ...............................................................
ø 6 mm Soft wood 20 mm .................................................................
Battery voltage ......................................................................................
Drill opening range ...............................................................................
Weight with battery ...............................................................................
Typical A-weighted sound levels:
Sound pressure level (K = 3 dB(A)) ....................................................
Sound power level (K = 3 dB(A)) ........................................................
Typical weighted acceleration in the hand-arm area ...........................
Measured values determined according to EN 60 745.
WARNING! Read all safety warnings and all
instructions, including those given in the accompanying
brochure. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes and
apron.
Wear ear protectors. Exposure to noise can cause hearing
loss.
Use auxiliary handles supplied with the tool. Loss of control
can cause personal injury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a live“ wire may make exposed metal parts of the power tool
live“ and shock the operator.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes
and apron.
Always wear goggles when using the machine. It is
recommended to wear gloves, sturdy non slipping shoes and
apron.
Sawdust and splinters must not be removed while the machine
is running.
When working in walls ceiling, or floor, take care to avoid
electric cables and gas or waterpipes.
Do not dispose of used battery packs in the household refuse
or by burning them. Milwaukee Distributors offer to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System PBS 3000 / V18 chargers for charging
System PBS 3000 / V18 battery packs.
No metal parts must be allowed to enter the battery section of
the charger (short circuit risk).
Never break open battery packs and chargers and store only in
dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme
load or extreme temperatures. In case of contact with battery
acid wash it off immediately with soap and water. In case of
eye contact rinse thoroughly for at least 10 minutes and
immediately seek medical attention.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust protection
mask.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized
documents. EN 60745, EN 55014-1, EN 55014-2, in
accordance with the regulations 98/37/EC, 2004/108/EC
Rainer Kumpf
Manager Product Development
Winnenden, 2009-01-14
*1 Measured according to Milwaukee norm N 877318
*2 The values stated are reference values.
Actual values might differ, depending on the material and quality of the screws.
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
SPECIFIED CONDITIONS OF USE
The battery screwdriver is designed for drilling and
screwdriving for independent use away from mains supply.
Do not use this product in any other way as stated for normal
use.
BATTERIES
Please take note of the specific information relating to
Milwaukee 18V rechargeable batteries in the instruction
manual for the charger.
New battery packs reach full loading capacity after 4 - 5
chargings and dischargings. Battery packs which have not
been used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure to
heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
ADVICE FOR OPERATION
Never use the gear switch whilst the machine is operating.
Only use the switch when the machine is at a standstill.
MAINTENANCE
Use only Milwaukee accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our Milwaukee service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on the
label and order the drawing at your local service agents or
directly at: Milwaukee Electric Tool, Max-Eyth-Straße 10,
D-71364 Winnenden, Germany.
SYMBOLS
Please read the instructions
carefully before starting the
machine.
Accessory - Not included in standard equipment,
available as an accessory.
Remove the battery pack before starting any
work on the machine.
Do not dispose of electric tools together with
household waste material! In observance of
European Directive 2002/96/EC on waste
electrical and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their
life must be collected separately and returned to
an environmentally compatible recycling facility.