Ultrasonic measuring tool 0520 introduction, Technical specifications, Safety – Skil 0520 AA User Manual

Page 5: Tool elements 3

Advertising
background image

Ultrasonic measuring tool

0520

INTRODUCTION

●

This tool is intended for measuring distances indoors by
means of ultrasonic waves

●

When used properly, this tool easily and accurately
measures length, surface and volume

●

Carefully read this instruction manual as well as the
warning label on the tool, before you use the tool

1

●

Pay special attention to the safety instructions and
warnings; failure to follow these may result in
serious (eye) injury

●

Save this instruction manual for future reference

TECHNICAL SPECIFICATIONS

Measurement range

0,5 to 15 m

Emergence angle of
ultrasonic signal

+/- 5°

Laser type

650 nm

Laser class

2

Maximum power output

≤

1 mW

Power supply

1x 6LR61/9V battery

Optimum operating
temperature

0 to 40°C

Weight

0,2 kg

Accuracy

maximum deviation of
+/- 0,5% / +/- 1 digit

SAFETY

●

Do not look into the laser beam (laser radiation)

2

●

Do not point the laser beam at persons or animals

●

Do not place the tool in a position that may cause
anyone to look into the laser beam intentionally or
unintentionally

●

Do not use any magnifying optical tools (such as
magnifying glasses, telescopes, or binoculars) to view
the laser beam

●

Do not remove or damage the warning label on the tool

●

Do not operate the tool in the presence of flammable
liquids, gases or dust

●

Do not operate the tool with children around

●

This tool should not be used by people under the age of
16 years

●

Do not use the tool for any purpose other than those
mentioned in this instruction manual

TOOL ELEMENTS

3

A Ultrasound opening
B Laser beam opening
C LCD display
D "Power" (on/off) key
E Metre/feet conversion key
F Single measurement mode
G Surface/volume computation mode

H Multiple measurement mode
J "Clear" (deletion) key
K "Read" (measurement) key
L "Recall" (review) key
M Bubble levels
N Warning label
P Battery compartment cover

USE

●

On/off
- switch on the tool by pressing "Power" button
- ambient temperature in °C is shown on display
- switch off the tool by pressing "Power" button again
- the tool automatically switches off after 30 seconds of

inactivity

●

Mounting of battery

4

! ensure that the tool is switched off
- remove cover P
- insert 9V battery (pay attention to correct polarisation)
- mount cover P
- when battery level is low, symbol

5

will appear in

display

! change battery in time, otherwise faulty

measurements may occur

- always remove the battery from the tool, if the tool is

not used for a long period

●

Metre/feet conversion
- measurements are in metres/centimetres by default
- press button E

3

for converting metres/centimetres

into feet/inches

- setting will not change as long as battery is not

removed from tool

●

Operating the tool

6

- press "Power" button
- select measurement mode (button F, G, or H)
- place rear edge of the tool on the starting-point of the

measurement

! aim the tool towards the target surface at a right

angle (use bubble levels M

3

)

- a laser "target"

7

is projected on the target surface

as an indication of where the ultrasonic signal is
reflected by the measured object

! do not look into the laser beam
! do not point the laser beam at persons or animals
- press "Read" button; measured distance appears on

top line of display

! keep in mind that the tool measures from its rear

(the tool length is included in the measuring result)

●

Instructions for proper measurement

6

! do not move the tool during measuring
! do not measure beyond the specified

measurement range (0,5 - 15 m)

! ensure that there are no obstructions within the

conical expanding sound range

- large, hard and flat surfaces give the most accurate

results

- place a piece of cardboard in front of the target

surface, when measuring small, soft or irregular
surfaces (such as carpets, curtains, coarse wallpaper,
etc.)

GB

5

SKIL_IB0520v2 07-01-2009 14:34 Pagina 5

Advertising