Candy LS CDF 735 P - 16 S User Manual
Page 13
24
WARNING!
If you open the door during the
drying cycle, an audible audio signal
advises you that the drying cycle has
not yet finished.
Changing a running programme
Proceed as follows to change or cancel a
running programme:
■
Hold down the current programme
button (with the indicator light on) for at
least 5 seconds. All programme indicator
lights will turn on for one second. The
running programme will be cancelled
and the corresponding indicator light will
start to flash. The display will go blank
and the programme end indicator light
will turn on in the display.
■
At this point a new programme can be set.
WARNING!
Before starting a new programme,
you should check that there is still
detergent in the dispenser.
If necessary, top up the dispenser.
If there is any break in the power supply
while the dishwasher is operating, a
special memory stores the selected
programme and, when the power is
restored, it continues where it left off.
Programme operations
When a programme is running, the time
until the end of the cycle will be displayed
and the 4
“PROGRAM STATUS”
indicator
lights:
= "WASH"
= "RINSE"
= "DRY"
=
"END"
will light
singularly and in sequence
to
indicate the current phase
Programme end
The display will go blank and the last
“PROGRAMME STATUS”
indicator light
will light to indicate that the cycle has
ended.
A 5 second alarm will sound (if not muted)
3 times at 30 second intervals to signal that
the programme has ended. The programme
end indicator light will light up and the
display will go blank.
Dishes can now be removed and the
dishwasher turned off by pressing the
"ON/OFF" button or dishes can be loaded
for a new cycle.
Option buttons
IMPORTANT
All options MUST be turned on or off,
BEFORE starting the programme.
“3 in 1” button
This option optimises the use of “3 in 1”/
“4 in 1”/“5 in 1” combined detergents. By
pressing this button, the selected washing
programme is modified to get the best
performance from combined detergents;
furthermore, the salt and rinse aid shortage
lights are de-activated.
WARNING!
Once selected, this option keeps
being on (light on) also for next
washing cycles and it can be de-activate
(light off) only by pressing the button
once again.
IMPORTANT
When this option is selected, the
"RAPID" cycle is 10 minutes longer.
"HPS" button
The "HPS" option always guarantees the
best results by more effectively dealing
with heavier soiling. By using this option,
the strength of the selected cycle will be
increased, adding one rinse and increasing
the temperature and water pressure in the
washing phase where foreseen.
This option is recommended for very dirty
dishes or when dirty dishes may not have
been pre-treated allowing the soiling to dry up.
IMPORTANT
With this option selected the “IMPULSE”
wash is turned off.
25
"1/2" button
In response to your everyday washing
requirement in addition to the normal wash
functions this dishwasher is equipped with
the “1/2” function. This function enables
the uses to wash a reduced number of
dishes yet retaining the freedom of loading
them both on the top and bottom basket.
When this function is activated the dishwasher
will automatically reduce the water and
energy consumption and the wash time.
When selecting the “1/2” ensure a reduced
amount of detergent is used.
"DELAY START" button
Dishwasher start time can be set with this
button, delaying start from 1 to 23 hours.
Proceed as follows to set a delayed start:
■
Press the "DELAY START" button ("00"
will appear on the display).
■
Press the button again to increase the
delay in hours (each time the button is
pressed the delay is increased by 1 hour
to a maximum of 23).
■
To start the countdown, press the
selected programme button (the relevant
indicator light will stop flashing and
remain on and the start time delay will be
shown in the display).
At the end of the countdown, the programme
will automatically start and the length of the
selected cycle will be shown in the display.
Proceed as follows to cancel a delayed
start:
■
Hold the selected programme button
down for at least 5 seconds.
■
Delayed start cancellation is confirmed
when the selected programme indicator
light starts to flash. The display will go
blank and the programme end indicator
light will light (any selected options will
also be cancelled and the corresponding
indicator lights will turn off).
■
At this point, a new programme and
option buttons must be set to start a
new programme as indicated in the
"PROGRAMME SETTINGS"
section.
Alarm mute for the PROGRAMME
END
The alarm for the programme end may be
muted as follows:
■
With the dishwasher off, hold down the
second option button (from the left) while
simultaneously pushing the "ON/OFF"
button.
■
"b1” will appear on the display to indicate
that the alarm is on.
■
Press the same option button (second
from the left) within 5 seconds ("b0" will
appear on the display to indicate that the
alarm is off).
■
Wait for the alarm to sound to indicate
that the settings were saved.
■
To turn the alarm on again, follow the
same procedure ("b1" will appear on the
display to indicate that the alarm is on).
WARNING!
To ensure the correct operation of
the anti-overflow safety device, we
recommend that the dishwasher is
not moved or tilted during operation.
If however it is necessary to tilt or
move the dishwasher, please ensure
that the washing cycle is complete
and that there is no remaining water
inside the dishwasher.