Candy LS CDI 1010 - S - Manual (Page 7)

12
Alarm mute
The alarm for the programme end may
be muted as follows:
IMPORTANT
The dishwasher must be ALWAYS off
before start this procedure.
1. Press the "ON/OFF" button.
2. Wait for the programme indicator lights
to start flashing.
3. WITHIN 2 MINUTES of switching the
machine on, hold down the
"PROGRAMME SELECTION" button
for at least 30 seconds (an intermittent
acoustic signal will sound).
4. When the 2 indicator lights on the left
will come on (to indicate that the alarm
is on) and the acoustic signal will stop to
sound, release the button.
5. Press the "PROGRAMME SELECTION"
button again.
The first 2 indicator lights from the left
will go off, while the other 2 indicator
lights will come on to indicate that the
alarm has been deactivated.
6. Wait for the alarm to sound to indicate
that the settings were saved (the
programme indicator lights will return to
flash).
7. To turn the alarm on again, follow the
same procedure.
WARNING!
If any problem occurs, turn the
dishwasher off by pressing the
"ON/OFF" button and start the
procedure again from the beginning.
Fault signals
If malfunctions or faults occur when a
programme is running the indicator light
that corresponds to the selected cycle
(2 indicator lights for the "COLD RINSE"
programme) will flash rapidly and the alarm
sounds.
In this event, turn the dishwasher off by
pressing the "ON/OFF" button. After
checking to make sure the water inlet hose
tap is open, that the drain hose is not bent
and that the siphon or filters are not
clogged, set the selected programme
again. If the anomaly persists, contact
Customer Service Department.
IMPORTANT
This dishwasher is equipped with an
anti-overflow safety device which will
automatically discharge any excess
water should a problem occur.
WARNING!
To ensure the correct operation of
the anti-overflow safety device, we
recommend that the dishwasher is
not moved or tilted during operation.
If however it is necessary to tilt or
move the dishwasher, please ensure
that the washing cycle is complete
and that there is no remaining water
inside the dishwasher.
According to the degree of hardness of
your water, regulate the softener unit in the
following way:
IMPORTANT
The dishwasher must be ALWAYS off
before start this procedure.
1. Press the "ON/OFF" button.
2. Wait for the programme indicator lights
to start flashing.
3. WITHIN 2 MINUTES of switching the
machine on, hold down the
"PROGRAMME SELECTION" button
(PR.) for at least 10 seconds (an
intermittent acoustic signal will sound).
4. When the 3 indicator lights on the left
will come on and the acoustic signal will
stop, release the button.
5. The light indicating the water softener
setting level will come on and the alarm
will shortly sound once. To change the
setting, press the "PROGRAMME
SELECTION" button: each time the
button is pressed, one indicator light
will come on (for level 5 all the indicator
lights will come on).
6. When the required setting is reached,
wait for the alarm to sound to indicate
that the settings were saved (the
programme indicator lights will return to
flash).
WARNING!
If any problem occurs, turn the
dishwasher off by pressing the
"ON/OFF" button and start the
procedure again from the beginning
(STEP 1).
13
WATER SOFTENER UNIT
Depending on the source of the supply,
water contains varying amounts of limestone
and minerals which are deposited on the
dishes leaving whitish stains and marks.
The higher the level of these minerals
present in the water, the harder the water is.
The dishwasher is fitted with a water
softener unit which, through the use of
special regenerating salt, supplies
softened water for washing the dishes.
The degree of hardness of your water can
be obtained from your water supply
company.
Regulating the water softener
with electronic programmer
The softener unit can treat water with a
hardness of up to 90°fH (French grading)
or 50°dH (German grading) through six
different settings.
The table below lists different degrees of
water hardness with the corresponding
setting for the softener unit.
*The water softener unit is set in the
factory at level 3, as this is suitable for
the majority of users.
Level
°fH
(French)
°dH
(German)
NO
YES
YES
YES
YES
YES
Indicator
light 1
Indicator
light 1
Indicator
light 2
Indicator
light 3
Indicator
light 4
Indicator
lights 1,2,3,4
Water
hardness
W
ater
softener setting Use of
regenerating
salt
0
1
2
*3
4
5
0-5
6-15
16-30
31-45
46-60
61-90
0-3
4-9
10-16
17-25
26-33
34-50
1 2 3 4
“PROGRAMME SELECTION” button
“ON/OFF”
button
Indicator lights