Remington PG6050 - Manual (Page 3)

4 5
ENGLISH ENGLISH
A CAUTION
Do not turn your trimmer on while charging through a USB port on your computer.
C HOW TO USE
,Attaching and removing guide combs
• With the trimmer blade facing away from you, slide the guide comb over the back of
the trimmer blade and click into position.
• With the trimmer blade facing away from you, carefully push the guide comb away from
the wide head trimmer.
,Before you begin
Comb facial hair with a fine comb before you start trimming. Hairs should be dry and without
any waxes or lotions before using the groomer.
,To thin and taper beards or moustaches
• Attach the wide trimmer blade.
• Place the hair length attachment on the trimmer blade, select the desired length and
switch on.
• Start trimming under the chin, following the jawbone line. Work toward the ear and
upper beard line using an upward motion.
,To Trim edge of beards or moustaches
• Attach the detail trimmer blade.
• Hold groomer with cutting blade facing you.
• Start with edge of beard/moustache line, and with the cutting blades resting lightly
against your skin, use slow movements to create a beard/moustache line.
,To trim sideburns
• Hold groomer with cutting blade facing you.
• Use a small comb to lift the hairs. Hold the comb at the desired beard or moustache
length.
• Move the groomer along the comb to cut the hairs. Use light pressure and
well-controlled movements to trim hair.
,Trimming the nape of your neck
• Attach the wide trimmer blade.
• Use your fingers to lift the hair at the base of your head up off the neck. Your index
finger should be covering the roots of the hairs you are lifting to prevent accidental
removal by groomer.
• Using your other hand, hold the groomer to the base of your neck with the cutting unit
facing up, and move the groomer up the length of the neck until the unit touches your
finger covering the hair roots at the base of your head. Move the unit slowly when
performing this operation and to keep the hair roots at the base of your head out of
the way of the groomer.
,To remove hair from nose and ear
• Attach nose, ear & eyebrow attachment.
• Insert groomer’s cutting unit gently into the nostril or ear.
• Gently move the groomer in and out of the nostril or ear and at the same time rotate
the groomer.
• Avoid inserting the cutting unit more than 6mm into your nostril or ear.
,To remove hair from eyebrows
• Attach nose, ear, eyebrow attachment.
• Gently guide cutting unit to stray, unwanted hairs along the eyebrow line or
protruding from the eyebrow itself.
• To remove the hairs completely lower onto the skin and move over desired area.
• Use slow and well-controlled movements.
E Tips for best results
Comb your hair in the direction that it grows so that the hairs are at their maximum height
and facing in the same direction.
After trimming, lightly go over the trimmed areas with the foil to get a smooth clean finish.
Since all hairs do not grow in the same direction, you may want to try different trimming
positions (i.e. upwards, downwards or across) for better results.
,Attaching and removing the trimmer attachments
Note: Always ensure the groomer is switched off before changing any attachments.
• To remove, hold the groomer with one hand and turn the trimmer head anti-clockwise
with the other.
• To attach, hold the groomer with on hand and turn the trimmer head clockwise with
the other.
,Using the detail attachment
• Hold groomer with the surface (back side) of the blade guides against the skin.
• Use motions similar to using a wet blade to provide the closest trim.
Note: The Trim Shave Technology attachment provides a dual purpose solution for
stubble or close results without irritation.
• Attach the comb to the detail trimmer making sure to keep the adjustable guard
orientated to the large cutting teeth, while covering the small cutting teeth.
• Once guard is in place, you can adjust the height of cut by using the thumb adjustment
button on the comb.