Activeforever Aquatec OceanVIP Tilt-In-Space Shower Commode Chair - Manual (Page 7)

13 EN
6.1 Adjusting the seat height
1. Slightly raise the commode at the seat frame.
2. Take out both clips (5, fig. 8).
3. To adjust the seat height, pull the seat frame out
of the side section (1, fig. 8) or push it in.
4. Align the clip recesses (3, fig. 8) at the side sec-
tion with a hole on the seat frame (4, fig. 8).
5. Push both clips from the outside into the side sec-
tion until the two lugs (6, fig. 8) enclose the seat
frame tube (2, fig. 8).
6.2 Adjusting the height of the footrests
1. Pull up the footrest (1, fig. 6) slightly.
2. Pull out the clip (7, fig. 6) and put it in again at the
required position. Pull out the footrest slightly fur-
ther if necessary.
3. Push down the footrest until the groove (2, fig. 6)
catches the pin of the clip (7, fig. 6).
4. Set the other footrest to the same height as de-
scribed.
6.3 Adjusting the inclination of the foot
plates
1. Loosen the Allen screw (3, fig. 6) on the foot plate
using a size 4 Allen key.
2. Turn the foot plate (4, fig. 6) to the desired posi-
tion.
3. Tighten the Allen screw again.
6.4 Adjusting the height of the armrests
1. Open the belt lock of the belt inside the backrest
frame at the backrest cover.
2. Open the belt lock of the belt above the armrests
at the backrest cover (1, fig. 9).
3. Feed this belt along the backrest frame and close
again.
4. Unscrew the screws (3, fig. 9) of the armrest hold-
er (4, fig. 9) using the supplied Allen key.
5. Remove the fastening clamp (2, fig. 9) with the
nuts from the inside of the backrest frame.
6. Remove the armrest holder (4, fig. 9) with the
armrest and move upwards.
7. Insert the screws into the armrest holder and
guide into the holes in the backrest frame.
8. Replace the nuts in the fastening clamp if neces-
sary.
9. Place the fastening clamp onto the backrest frame
so that the fixing of the fastening clamp engages
with the small hole.
10. Insert the screws into the nuts and tighten.
11. Guide the belt of the backrest cover around the
back rest frame, close it and then tighten all the
belts.
Follow the same procedure to adjust the armrests to
the lower position.
Important!
● The seat height must be adjusted to suit the
user. As a rule, the seat height is correctly
adjusted when the user is sitting on the
commode and both feet touch the ground.
● The seat height must be adjusted on both
sides simultaneously. To make adjust-
ments, a second person is required to help.
● Do not adjust the seat height of the com-
mode
when someone is sitting on it.
Important!
● The inclination of the foot plates can be ad-
justed infinitely variably.
● The right and left foot plates must be ad-
justed in the same way.
6 Operation
Important!
● The height of the armrests must be adjust-
ed to suit the user.
● The height of the armrests must be adjust-
ed by the same amount on both sides.
● The height of the right and left armrest is
adjusted in the same way.
Important!
The nuts are inserted loosely in the fastening
clamp and can fall out.
Important!
The small hole is for fixing the fastening clamp.
Important!
Open the belt below the armrest and feed it
through the backrest frame if you are adjusting
the armrest to the lower position.