Altronix ALTV248220 Series Installation Instructions User Manual
Page 2
- 2 -
ALTV248220series
Overview:
These Altronix CCTV Power Supplies provide provide 24VAC/28VAC distributed via eight (8) fuse or PTC protected
outputs for powering CCTV Cameras, heaters and other video accessories.
Eight (8) Output ALTV248220 Reference Chart:
Specifications:
Altronix
Model Number
• Surge suppression.
• AC power LED indicator.
• Illuminated power disconnect circuit breaker with
manual reset.
• Unit maintains camera synchronization.
• Ease of installation saves time & eliminates costly labor.
• Spare fuses included (on fuse protected models).
Enclosure Dimensions:
ALTV248220, ALTV248CB220, ALTV248175220
and ALTV248175CB220: 216mm x 191mm x 89mm
ALTV248300M220 and ALTV248300CBM220:
216mm x 191mm x 95mm
ALTV248300220 and ALTV248300CB220:
311mm x 197mm x 114mm
ALTV248600220 and ALTV248600CB220:
343mm x 330mm x 83mm
ALTV248220
24VAC
4 amp
8
-------
P
3.5 amp
5 amp/250V
0.5 amp
28VAC
3.5 amp
ALTV248CB220
24VAC
4 amp
8
P
-------
2.5 amp
5 amp/250V
0.5 amp
28VAC
3.5 amp
ALTV248175220
24VAC 7.25 amp
8
-------
P
3.5 amp
10 amp/250V
0.7 amp
28VAC 6.25 amp
ALTV248175CB220
24VAC 7.25 amp
8
P
-------
2.5 amp
10 amp/250V
0.7 amp
28VAC 6.25 amp
ALTV248300220
24VAC
14 amp
8
-------
P
3.5 amp
15 amp/32V
1.35 amp
28VAC 12.5 amp
ALTV248300CB220
24VAC
14 amp
8
P
-------
2.5 amp
15 amp/32V
1.35 amp
28VAC 12.5 amp
ALTV248300M220
24VAC 12.5 amp
8
-------
P
3.5 amp
15 amp/32V
1.35 amp
28VAC
10 amp
ALTV248300CBM220
24VAC 12.5 amp
8
P
-------
2.5 amp
15 amp/32V
1.35 amp
28VAC
10 amp
ALTV248600220
24VAC
28 amp
8
-------
P
3.5 amp
(2) 15 amp/32V
2.7 amp
28VAC
25 amp
ALTV248600CB220
24VAC
28 amp
8
P
-------
2.5 amp
(2) 15 amp/32V
2.7 amp
28VAC
25 amp
Output
Voltage
Total
Output
Current
(Power)
Number
of
Outputs
PTC
Protected
Outputs Fuse
Protected
Outputs Output
Current
(max.
per
output)
Main
Fuse
Ratings
on
Board
220VAC
50/60Hz
Input
Current
Installation Instructions:
1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 6-8).
Secure enclosure to earth ground.