ViTESSE VS-663 - Manual (Page 2)

Description of device
1. Spray organ
2. Filler door
3. Shot-steam button
4.
Spray button
5. Steam dial
6. Cord bushing
7. Supply cord
8.
Plate temperature control light
9. Transparent water tank
10. Thermostat knob for temperature regulation
11. Self-cleaning
12. Maximum filling level
13. Plate with steam vents
14. Water measure
P/1 P/2
Special instructions
1. To avoid a circuit overload, do not operate another high wattage
appliance on the same circuit.
2. If an extension cord is absolutely necessary, a 10-ampere cord should be
used. Cords rated for less amperage may overheat. Care should be taken
to arrange the cord so that it cannot be pulled or tripped over..
Save these instructions
More specifically:
DO NOT let children or untrained persons use the appliance without
supervision.
NEVER immerse the iron, cable or plug in any liquid.
DO NOT leave the hot iron touching fabrics or very inflammable surfaces.
DO NOT leave the appliance unnecessarily plugged in. Disconnect the plug
from the mains when the appliance is not being used.
NEVER touch the appliance with wet or damp hands.
DO NOT use the power cord or the appliance in order to pull the plug out of the
socket.
DO NOT leave the appliance exposed to the weather (rain, sun, etc. ).
DO NOT leave the iron without supervision when it is connected to the power
supply.
DO NOT fill the reservoir with water before removing the plug from the socket.
Please note!
Do not use chemical additive, scented substances or decalcifiers. Failure to
comply with the above-mentioned regulations leads to the loss of guarantee.
MA X
(7) (6)
(8)
(5)
(4)
(3)
(2)
(1)
(13) (12) (11) (10) (9)
(14)
DEAR CUSTOMER!
You have made an excellent decision. Vitesse® “Nouveau” home range offers
you an exclusive, high quality range of appliances for your ultimate home
luxury and healthy living.
Important safety instructions
When using your flatiron, basic safety precautions should always be followed,
including the following:
Read all instructions before using
1. Use iron only for its intended use.
2. To protect against a risk of electric shock, do not immerse the iron in water
or other liquids.
3. The iron should always be turned to «Off» before plugging or unplugging
from outlet. Never yank cord to disconnect from outlet; instead, grasp plug
and pull to disconnect.
4. Do not allow cord to touch hot surfaces. Let iron cool completely before
putting away. Loop cord loosely around iron when storing.
5. Always disconnect iron from electrical outlet when filling with water or
emptying and when not in use.
6. Do not operate iron with a damaged cord or if the iron has been dropped or
damaged. To avoid the risk of electric shock, do not disassemble the iron
take it to a qualified serviceman for examination and repair. Incorrect
reassembly can cause a risk of electric shock when the iron is used.
Close supervision is necessary for any appliance being used by or near
children. Do not leave iron unattended while connected or on an ironing
board.
Burns can occur from touching hot metal parts, hot water, or steam. Use
caution when you turn a steam iron upside down there may be hot water in
the reservoir.
9. If the malfunction indicator goes on, the flatiron is not operating normally.
Disconnect from the power supply and have the flatiron serviced by
qualified service personnel.
10. The iron must be used and rested on a stable surface.
11. When placing the iron on its stand, ensure that the surface on which the
stand is placed is stable.
12. The iron is not to be used if it has been dropped, if there are visible signs of
damage or if it is leaking.
13. This appliance is not intended for use by persons (including children) with
reduced physical,sensory or mental capabilities,or lack of experience and
knowledge,unless they have been given supervision or instruction
concerning use of the appliance by a perliance by a person responsible for
their safety.
14. children should be supervised to ensure that they do not play with the
appliance.
15. If the supply cord is damaged,it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
7.
8.