Milton CAT 994F - Manual (Page 22)

22 994F Wheel Loader specifications
Operating Specifications – Standard Lift
For machines equipped with 53.5/85-57, 76 PR L-5 tires – see additional tables for other tire sizes
Coal Bucket
Narrow Bucket Wide Bucket (6200 mm/
(5640 mm/222 in) (6200 mm/244 in) 244 in)
Straight
Edge
Coal
Spade Edge Spade Edge Bucket
Rock Bucket Rock Bucket Teeth &
Teeth & Segment Teeth & Segment Segment
Rated capacity (§) m 3 14 15 17 19 18 19 31
yd 3 18.5 19.5 22.5 25 23.5 25 41
Width (§) mm 5640 5640 5640 5640 6200 6200 6200
ft/in 18' 6" 18' 6" 18' 6" 18' 6" 20' 4" 20' 4" 20' 4"
Struck capacity (§) m 3 11 12 14 15 14.5 15 27
yd 3 14.4 15.7 18.3 19.6 19.0 19.6 35.3
Dump clearance at full lift mm 5771 5771 5663 5556 5663 5563 5635
and 45 ° discharge (§) ft/in 18' 11" 18' 11" 18' 7" 18' 3" 18' 7" 18' 3" 18' 6"
Reach at full lift mm 2071 2071 2160 2266 2160 2278 2306
and 45
° discharge (§)
ft/in 6' 9" 6' 9" 7' 1" 7' 5" 7' 1" 7' 6" 7' 6"
Reach with lift arms mm 4916 4916 5056 5206 5056 5210 5179
horizontal and bucket level ft/in 16' 1" 16' 1" 16' 7" 17' 0" 16' 7" 17' 1" 17' 0"
Digging depth (§) mm 108 108 108 108 108 108 63
in 4" 4" 4" 4" 4" 4" 2"
Overall length (§) mm 16 604 16 604 16 744 16 894 16 744 16 898 16 830
ft/in 54' 6" 54' 6" 54' 11" 55' 5" 54' 11" 55' 5" 55' 2"
Overall height with bucket mm 10 719 10 719 10 866 10 911 10 636 10 621 10 960
at full raise (§) ft/in 35' 2" 35' 2" 35' 7" 35' 9" 34' 11" 34' 10" 39' 11"
Loader clearance circle with mm 12 668 12 668 12 704 12 742 12 965 13 002 13 073
bucket in carry position (§) ft/in 41' 7" 41' 7" 41' 8" 41' 9" 42' 6" 42' 7" 42' 11"
Static tipping load straight** (§) kg 130 783 131 140 130 266 128 499 127 909 126 522 129 295
lb 288,327 289,114 287,187 283,292 281,991 278,933 285,046
Static tipping load kg 113 391 113 684 112 784 111 091 110 539 109 241 111 719
at full 40
° turn** (§)
lb 250,188 250,835 248,849 245,113 243,895 241,032 246,298
Breakout force*** (§) kN 1134 1133 1055 989 1060 995 974
lb 254,993 254,709 237,173 222,336 238,289 223,685 218,964
Operating weight** (§) kg 191 899 192 039 192 699 193 779 193 999 194 729 195 169
lb 423,064 423,373 424,828 427,209 427,694 429,303 430,273
(§) Specifications rating conform to all applicable standards recommended by the Society of Automotive Engineers. SAE standard J732c governs loader ratings
and is denoted in the chart by (§).
* Dimensions are measured to the tip of the bucket teeth to provide accurate clearance data. SAE standard specifies the cutting edge.
** Static tipping load and operating weight shown are based on standard machine configuration with 53.5/85-57 tires, full fuel tank, coolant and lubricants.
*** Measured 102 mm (4 in) behind tip of cutting edge with the bucket hinge pin as pivot point in accordance with SAE J732c.