Yamaha DG100-212 - Manual (Page 6)

6
■ Front Panel
q Input Jack (INPUT HIGH, LOW)
Connect the guitar to this jack. Guitars with a high output level should be
connected to the LOW jack. Those with low output levels should be con-
nected to the HIGH jack.
* Switch the power OFF before connecting the guitar.
w Trim Control (TRIM)
Used to match the guitar’s output level to the pre-amp’s input level. ( →
page 8.)
* TRIM level settings are not stored in memory.
e Output Level Control (OUTPUT)
Used to control the output volume of the power amp.
Sets the amount of output of sound created by the preamp’s GAIN,
MASTER, Tone Controls, etc. The volume is controlled without chang-
ing the tonal quality of the amp.
* Output level settings are not stored in memory.
* Has no affect on the level (volume) of the LINE OUT @4 jack.
r Gain Volume (GAIN)
Used to control the amount of distortion.
* Sound is not produced if the GAIN is set to 0, even when the MASTER VOL-
UME
t is turned up.
t Master Volume (MASTER)
Used to control the overall volume of GAIN and tone control settings. It
also controls the output level of the preamp.
* Master level settings are stored in memory.
y Tone Controls
(TREBLE, HIGH MID, LOW MID, BASS, PRESENCE)
Used to control the levels of their respective frequencies.
When the Tape Echo Mode is engaged, the BASS and PRESENCE
knobs are used to adjust the tape echo’s TIME and FEEDBACK set-
tings. ( → page 8.)
u Reverb Volume (REVERB)
Used to control the amount of the reverb. ( → page 8.) When the Tape
Echo Mode is engaged, the REVERB knob is used to adjust the tape
echo’s LEVEL setting. ( → page 8.)
i Amp Select Button/Amp Select Display
(LEAD 1, 2/DRIVE 1, 2/CRUNCH 1, 2/CLEAN 1, 2)
Used to select one of the eight preset amp types. The currently se-
lected amp type is shown on the display. ( → page 8.)
When the Utility Mode is engaged, these switches are used to switch
MIDI functions and the Speaker Simulator ON or OFF, etc. ( → page 11.)
* When the Amp Select button is pressed, knobs r – y return to their preset
positions (GAIN and MASTER =7, Tone Controls all = 5). The position of
the REVERB knob does not change.
w e r t y u q i o !0
!2 !1
!3 !4 !5
!6
!7
The Panel Controls
o Reverb Type Select Button (REVERB)
!0 Reverb Type Display Lamp (SPRING, HALL, PLATE)
Press the button to select the reverb type. The lamp corre-
sponding to the selected reverb type will light. ( → page 8.)
!1 Mode Select Button (MODE)
!2 Mode Display Lamp (AMP/TAPE ECHO/UTIL.)
Displays the currently selected mode.
• AMP (Amp Mode)
Normal playing mode. All knobs and buttons on the panel function as
marked. (Dual function knobs and buttons will function according to
their upper indications.)
This mode is automatically engaged whenever a memory is recalled.
• TAPE ECHO (Tape Echo Mode) → page 8
The Tape Echo setting mode.
When in the Amp Mode, press the button once and quickly
release to enter the Tape Echo Mode.
• UTIL. (Utility Mode) → page 11
This mode is used to set MIDI functions and switch Speaker Simula-
tion ON or OFF. When in the Amp Mode or Tape Echo Mode, press
the button and hold for about one second to enter the Utility
Mode.
!3 Display
Displays Memory Numbers, Program Change Numbers, the MIDI Chan-
nel, etc.
!4
/ Buttons
Increases or decreases the memory number by 1. Also, increases or
decreases values by 1. In the Utility Mode increases/decreases values
by 1 or sets the function ON/OFF. Values change continuously when the
button is pressed and held.
!5 Store Button (STORE)
Press this button to save current sound settings to internal memory. ( →
page 9.) Also, used to carry out MIDI Bulk Out operations. ( → page 11.)
!6 Recall Button (RECALL)
Recalls the settings stored in memory. Use the / buttons to se-
lect a memory number (01 – 128), then press the button to
recall those settings from memory. ( → page 9.)
!7 Power Switch (POWER)
The power switch for the DG100-212.
* To protect the speakers from possible damage, always set the OUTPUT e
volume to “0” before turning the power ON/OFF.