Bty series br o adb and antenn as – Toner Cable BTY-C-MOUNT 5760 Antenna Mount User Manual
Page 2
Toner Cable Equipment, Inc.
Specifications Subject To Change Without Notice.
Telephone:
Nationwide:
Fax:
E-mail:
Internet:
BTY SERIES BR
O
ADB
AND ANTENN
AS
215-675-2053
800-523-5947
215-675-7543
http://www.tonercable.com
ORDERING INFORMATION:
BTY-2-FM
Stock No. 4878
FEATURES:
Full 88-108 MHz Coverage
360° Beamwidth
Fiber Filled Elements
Dampen Vibration
ORDERING INFORMATION:
BTY-C-MOUNT
Stock No. 5760
FEATURES:
Antenna Cantilever Mount-
Allows Antennas to Mount
Directly to Tower
Maximizes Signal Reception by
Keeping Elements Clear of
Support Structures
Vertical or Horizontal Mounting
BTY-MC
Stock No. 4879
FEATURES:
Stainless Steel Antenna
Mounting Clamp
Allows Stacking of BTY Series
Antennas
BTY-2-FM
FM ANTENNA
The BTY-2-FM is a professional quality, FM band antenna designed specifically for FM
reception applications. This antenna covers the entire FM band from 88 to 108 MHz
using two half-wave dipole elements mounted 90° to one another. This design give
the BTY-2-FM an omnidirectional (360°) reception path.
The BTY-2-FM is supplied complete with two dipole elements, an 18” square boom,
universal mounting bracket and connector cable. The heavy duty mounting bracket is
designed for either vertical or horizontal tower members and will attach to masts up to 2.5” inches in
diameter. The BTY Series Antennas can accommodate a maximum mast size of 2.5” O.D. (outside
diameter). These antennas feature a 75
Ω
type “F” connector to provide feed on coaxial cable down
leads.
5760
4879
SPECIFICATIONS
ELECTRICAL
BTY-2-FM
Units
Gain Over Isotropic:
2.2
dBi
Bandwidth:
88-108
MHz
Beamwidth (-3 dB):
360° azimuth
°
VSWR:
1.67:1
Return Loss:
12.0
dB
Impedance:
75
W
MECHANICAL
Boom:
6063-T6 alum. tube,
1.25” square, 0.062” wall
Boom Length:
18.0
in
Number of Elements:
2
Elements:
6063-T52 alum. tube,
0.5” round, 0.049” wall
MECHANICAL
(continued)
BTY-2-FM
Units
Maximum Element Width: 59.0
in
Turning Radius:
29.0
in
Max. Cross Sectional Area: 0.463
sq. feet
Operational/Survival
Wind Velocity:
125
mph
Output Connector:
Type “F”, female,
weather sealed
Max. Mast Diameter (O.D.): 2.5”
Shipping Weight:
3.00
lbs
1.36
kg
Shipping Size:
60 x 4.0 x 5.5
in
(LxHxW)
152 x 10 x 14
cm
BTY-C-MOUNT
ANTENNA MOUNT
The BTY-C-MOUNT consists of a heavy duty
square aluminum boom and all clamping hard-
ware required for rear mounting of the follow-
ing BTY Series Antennas: BTY-5-LB, BTY-10-
HB, BTY-LP-LB, BTY-LP-HB, and BTY-LP-BB.
Cantilever end-mounting is commonly used
since the antennas are usually attached to
tower legs rather than to masts. This maxi-
mizes the signal reception qualities of the
antenna by keeping elements clear of support
structures. It also eliminates the need for out-
riggers and masts. Antennas can be mounted
horizontally or vertically on a tower leg or mast
(1.25” to 2.5” O.D.) by rotating the mounting
plate 90°. The BTY-C-MOUNT is designed to
mount parallel to and below the antenna boom.
SPECIFICATIONS
MECHANICAL
BTY-C-MOUNT
Units
Boom:
6063-T6 alum. tube,
1.25” square, 0.062” wall
Boom Length:
63.38
in
Mounting Plates
14 gauge (0.074”)
and Brackets:
stainless steel
Max. Cross
Sectional Area:
0.88
sq. feet
Wind Resistance
(@ 100 mph):
58.2
lbs
Shipping Weight:
8.31
lbs
3.78
kg
BTY-MC
ANTENNA MOUNT
The BTY-MC is a heavy duty, stainless steel
antenna mounting clamp designed for stacking
BTY Series Antennas. The resultant antenna
array improves antenna gain for use in fringe
areas. The BTY-MC has excellent weathering
properties and exceptional strength. The num-
ber of clamps needed is dependent on the
number of antennas stacked (i.e. 2 antenna
array uses 3 clamps, a 4 antenna array uses 6
clamps). The BTY-MC is shipped completely
pre-assembled and has a compact design for
ease of mounting.
SPECIFICATIONS
MECHANICAL
BTY-MC
Units
Material:
stainless steel
Mount Dimensions:
6 x 6 x 1.38
in
152 x 152 x 35
mm
U-Bolts:
Quantity:
4
Size:
0.38
in diameter
Maximum Tubing Size:
2.5
in O.D.
Shipping Weight:
2.5
lbs
1.14
kg
4878