Detailed description, Pin description – Rainbow Electronics MAX5104 User Manual

Page 6

Advertising
background image

MAX5104

Low-Power, Dual, Voltage-Output, 12-Bit DAC
with Serial Interface

6

_______________________________________________________________________________________

_______________Detailed Description

The MAX5104 dual, 12-bit, voltage-output DAC is easily
configured with a 3-wire serial interface. The device
includes a 16-bit data-in/data-out shift register, and
each DAC has a double-buffered input composed of an
input register and a DAC register (see

Functional

Diagram). In addition, trimmed internal resistors produce
an internal gain of +2V/V that maximizes output voltage
swing. The amplifier’s offset-adjust pin allows for a DC
shift in the DAC’s output.

Both DACs use an inverted R-2R ladder network that
produces a weighted voltage proportional to the input
voltage value. Each DAC has its own reference input to
facilitate independent full-scale values. Figure 1 depicts
a simplified circuit diagram of one of the two DACs.

Reference Inputs

The reference inputs accept both AC and DC values
with a voltage range extending from 0 to (V

DD

- 1.4V).

Determine the output voltage using the following equa-
tion (OS_ = AGND):

V

OUT

= (V

REF

·

NB / 4096)

·

2

where NB is the numeric value of the DAC’s binary input
code (0 to 4095) and V

REF

is the reference voltage.

The reference input impedance ranges from 14k

Ω

(1554

hex) to several gigohms (with an input code of 0000
hex). The reference input capacitance is code depen-
dent and typically ranges from 15pF with an input code
of all zeros to 50pF with a full-scale input code.

Output Amplifier

The MAX5104’s output amplifiers have internal resistors
that provide for a gain of +2V/V when OS_ is connected
to AGND. These resistors are trimmed to minimize gain
error. The output amplifiers have a typical slew rate of
0.75V/µs and settle to 1/2LSB within 15µs, with a load
of 10k

Ω

in parallel with 100pF. Loads less than 2k

Ω

degrade performance.

The OS_ pin can be used to produce an adjustable off-
set voltage at the output. For instance, to achieve a 1V
offset, apply -1V to the OS_ pin to produce an output
range from 1V to (1V + V

REF

·

2). Note that the DAC’s

output range is still limited by the maximum output voltage
specification.

Power-Down Mode

The MAX5104 features a software-programmable shut-
down mode that reduces the typical supply current to
2µA. The two DACs can be powered down indepen-
dently, or simultaneously using the appropriate pro-
gramming command. Enter power-down mode by
writing the appropriate input-control word (Table 1). In
power-down mode, the reference inputs and amplifier
outputs become high impedance, and the serial inter-
face remains active. Data in the input registers is saved,

Digital Ground

DGND

9

Serial-Data Output

DOUT

10

User-Programmable Output

UPO

11

Power-Down Lockout. The device can-
not be powered down when

PDL is low.

PDL

12

Reference for DAC B

REFB

13

Active-Low Clear Input. Resets all reg-
isters to zero. DAC outputs go to 0V.

CL

5

Chip-Select Input

CS

6

Serial-Data Input

DIN

7

Serial-Clock Input

SCLK

8

Reference for DAC A

REFA

4

DAC A Offset Adjustment

OSA

3

PIN

DAC A Output Voltage

OUTA

2

Analog Ground

AGND

1

FUNCTION

NAME

14

OSB

DAC B Offset Adjustment

15

OUTB

DAC B Output Voltage

16

V

DD

Positive Power Supply

OUT_

OS_

R

R

D0 D10

D11

D12

2R

2R

2R

2R

2R

R

R

R

REF_

AGND

Figure 1. Simplified DAC Circuit Diagram

_____________________Pin Description

Advertising